MULTI-MODE MANUAL TRANSAXLE SYSTEM Multi-Mode Manual Transmission Warning Light Circuit
| DTC Code | DTC Name |
|---|---|
| Multi-Mode Manual Transmission Warning Light Circuit |
DESCRIPTION
The combination meter interprets the multi-mode manual transaxle system condition according to the information from the INDC and INDA circuits, and if necessary, illuminates (blinks) the multi-mode manual transaxle warning light and sounds the buzzer.
INDC Terminal Circuit:
The battery voltage is constantly supplied to the INDC circuit. If the INDC circuit is open, the combination meter detects a malfunction in the circuit and illuminates the multi-mode manual transaxle warning light. The INDC circuit is used to send the multi-mode manual transaxle warning light signal to the combination meter when the ignition switch is off.
INDA Terminal Circuit:
Power is supplied to the INDA circuit when the ignition switch is ON. While the ignition switch is ON, the combination meter controls the multi-mode manual transaxle warning light ON/OFF condition according to the signal from the INDA circuit. The INDA circuit is used to send the signal for multi-mode manual transaxle warning light and shift position indicator to the combination meter.
The contents of signals from the INDC and INDA circuits, and the status of the multi-mode manual transaxle warning light, buzzer and indicator are shown in the table below.
INDA circuit state (at combination meter) |
Normal |
Inconsistent signal input (3 seconds or more) |
Interrupted signal input (3 seconds or more) |
|||
INDC circuit (at combination meter) |
Normal |
+B short or open |
Normal |
+B short or open |
Normal |
+B short or open |
Shift position indicator *1 |
ON depends on communication signal |
ON depends on communication signal |
OFF |
OFF |
OFF |
OFF |
Multi-mode manual transaxle warning light |
ON depends on communication signal |
ON depends on communication signal |
ON |
ON |
ON |
ON |
Buzzer (Built into combination meter) |
ON depends on communication signal |
ON depends on communication signal |
OFF |
OFF |
OFF |
OFF |
*1: When the shift position indicator is turned ON, the number or letter segments are illuminated.
INDA circuit state (at combination meter) |
Normal |
Inconsistent signal input (3 seconds or more) |
Interrupted signal input (3 seconds or more) |
|||
INDC circuit state (at combination meter) |
Normal |
+B short or open |
Normal |
+B short or open |
Normal |
+B short or open |
Shift position indicator *1 |
ON depends on communication signal |
ON depends on communication signal |
OFF |
OFF |
OFF |
OFF |
Multi-mode manual transaxle warning light |
ON depends on communication signal |
ON |
ON |
ON (turns OFF 4 seconds or more after IG OFF*2) |
ON |
ON (turns OFF 4 seconds or more after IG OFF*2) |
Buzzer (Built into combination meter) |
ON depends on communication signal |
ON depends on communication signal |
ON |
ON (turns OFF 4 seconds or more after IG OFF*2) |
ON |
ON (turns OFF 4 seconds or more after IG OFF*2) |
*1: When the shift position indicator is turned ON, the number or letter segments are illuminated.
*2: The ignition switch is turned off.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
Check that the multi-mode manual transaxle warning light and shift position indicator light come on.
Under normal conditions, the shift position indicator indicates the current gear position when the ignition switch is ON, and the multi-mode manual transaxle warning light comes on for bulb check for approximately 5 seconds when the ignition switch is turned from off to ON.
If the shift position indicator light does not come on, the INDA circuit may be malfunctioning. If the multi-mode manual transaxle warning light does not come on, the INDA and/or INDC circuits may be malfunctioning.
PROCEDURE
CHECK HARNESS AND CONNECTOR (TCM - COMBINATION METER ASSEMBLY)
Disconnect the TCM connector.
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection
Condition
Specified Condition
A26-29 (INDC) - E12-32 (BRQ)
Always
Below 1 Ω
A26-31 (INDA) - E12-31 (TX+)
Always
Below 1 Ω
A26-29 (INDC) - Body ground
Always
10 kΩ or higher
A26-31 (INDA) - Body ground
Always
10 kΩ or higher
Result
Proceed to
OK
NG
NG REPAIR OR REPLACE HARNESS OR CONNECTOR
INSPECT COMBINATION METER ASSEMBLY
-
*a
Component with harness connected
(Combination Meter Assembly)
Reconnect the combination meter assembly connector.
Measure the voltage according to the value(s) in the table below.
Standard Voltage
Tester Connection
Condition
Specified Condition
E12-31 (TX+) - Body ground
Ignition switch off
Below 1.44 V
E12-31 (TX+) - Body ground
Ignition switch ON
3.64 V or higher
E12-32 (BRQ) - Body ground
Always
Below 1.44 V
Result
Proceed to
OK
NG
-