LIGHTING SYSTEM

DTC Code DTC Name
INITIALIZATION

CAUTION / NOTICE / HINT

Note:

  • Initialize the height control sensor signal after the vehicle height changes due to replacement of the suspension or after performing such operations as removal and reinstallation or replacement of the rear height control sensor sub-assembly.

  • Initialization is also necessary when the headlight leveling ECU is replaced.

  • Adjust the headlight aim after initializing the headlight leveling ECU.

  • When a malfunction is detected in the automatic headlight beam level control system, the height control sensor signal initialization is impossible. Perform troubleshooting before initialization.

PROCEDURE

  1. HEIGHT CONTROL SENSOR SIGNAL INITIALIZATION

    Tip:

    When performing initialization of the headlight leveling ECU using the intelligent tester, starting initialization is possible without lowering the fuel amount to below 10 liters (10.6 US qts, 8.8 Imp.qts).

    Result

    Proceed to

    WHEN NOT USING INTELLIGENT TESTER

    WHEN USING INTELLIGENT TESTER
    WHEN USING INTELLIGENT TESTER

    PREPARE VEHICLE FOR INITIALIZATIONClick here

    WHEN NOT USING INTELLIGENT TESTER

  2. PREPARE VEHICLE FOR INITIALIZATION

    1. Make sure that approximately 10 liters (10.6 US qts, 8.8 Imp.qts) of fuel is in the tank.

    2. Unload the trunk and vehicle, and make sure that the spare tire, tools and jack are in their original positions.

    3. Check that there are no occupants in the vehicle.

    4. Turn off the headlights.

    5. Stop the vehicle on a level surface and keep the vehicle height unchanged.

    Result

    Proceed to

    NEXT
    NEXT

  3. CHECK WARNING LIGHT

    1. Turn the ignition switch to ON and check the headlight beam level control system warning light.

      OK

      Condition

      Specified Condition

      The headlight leveling ECU is replaced with a new one.

      Warning light continuously blinks 6 times at 2 Hz.

      Removal and reinstallation of the headlight leveling ECU, replacement of the rear height control sensor sub-assembly, removal and reinstallation of the rear height control sensor sub-assembly, replacement of the suspension, etc.

      Warning light comes on for approximately 3 seconds, and then turns off (bulb check function).
      Tip:

      • If the warning light does not come on when turning the ignition switch to ON, perform inspections and repairs according to "Problem Symptoms Table".

        Click here

      • If there is a problem with the initialized data memorized in the headlight leveling ECU, the warning light blinks 6 times at 2 Hz when the ignition switch is turned to ON.

    Result

    Proceed to

    OK

    NG
    NG

    GO TO PROBLEM SYMPTOMS TABLE

    Click here

    OK

  4. INITIALIZATION

    1. E106867E12

      Connect terminals 4 (CG) and 8 (LVL) of the DLC3 using SST.

    2. Flash the low beam headlights 3 times within 20 seconds with the light control switch after connecting the terminals.

      Note:

      • Turn the low beam headlights on and off at approximately 1-second intervals.

      • Be sure to operate the light control switch from the outside of the vehicle.

    3. Check the warning light.

      OK

      Condition

      Specified Condition

      The headlight leveling ECU is replaced with a new one.

      Blinks 6 times at 2 Hz → Blinks 3 times at 2 Hz, and then turns off.

      Removal and reinstallation of the headlight leveling ECU, replacement of the rear height control sensor sub-assembly, removal and reinstallation of the rear height control sensor sub-assembly, replacement of the suspension, etc.

      Off → Blinks 3 times at 2 Hz, and then turns off.
      Tip:

      • If the calculated vehicle height is not within the acceptable range, the height control sensor initialization will end as an abnormal termination, and the warning indicator will blink 6 times at 2 Hz continuously. Disconnect SST from the DLC3 and turn the ignition switch off. Then restart from "Check Warning Light".

      • If initialization cannot be finished normally, check the LVL terminal circuit (Click here), or perform inspections and repairs according to "Problem Symptoms Table" (Click here)

    09843-18040

    Result

    Proceed to

    OK

    NG
    OK

    END

    NG

    PERFORM TROUBLESHOOTING

    Click here

  5. PREPARE VEHICLE FOR INITIALIZATION

    1. Unload the trunk and vehicle, and make sure that the spare tire, tools and jack are in their original positions.

    2. Check that there are no occupants in the vehicle.

    3. Turn off the headlights.

    4. Stop the vehicle on a level surface and keep the vehicle height unchanged.

    Result

    Proceed to

    NEXT
    NEXT

  6. CHECK WARNING LIGHT

    1. Turn the ignition switch to ON and check the headlight beam level control system warning light.

      OK

      Condition

      Specified Condition

      The headlight leveling ECU is replaced with a new one.

      Warning light continuously blinks 6 times at 2 Hz.

      Removal and reinstallation of the headlight leveling ECU, replacement of the rear height control sensor sub-assembly, removal and reinstallation of the rear height control sensor sub-assembly, replacement of the suspension, etc.

      Warning light comes on for approximately 3 seconds, and then turns off (bulb check function).
      Tip:

      • If the warning light does not come on when turning the ignition switch to ON, perform inspections and repairs according to "Problem Symptoms Table".

        Click here

      • If there is a problem with the initialized data memorized in the headlight leveling ECU, the warning light blinks 6 times at 2 Hz when the ignition switch is turned to ON.

    Result

    Proceed to

    OK

    NG
    NG

    GO TO PROBLEM SYMPTOMS TABLE

    Click here

    OK

  7. INITIALIZATION

    1. Turn the ignition switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON and push the intelligent tester main switch on.

    4. Enter the following menus: Body / HL Auto Leveling / Utility / Height Sensor Initialization / Next.

    5. Check what is displayed on the screen of the intelligent tester and press "Next".

    6. E183424

      Check the fuel level of the fuel receiver gauge in the combination meter. The appropriate position ID is determined by the present fuel level.

      Fuel Level

      Position ID

      Fuel level is within range A.

      FULL to over 3/4

      Fuel level is within range B.

      3/4 to over 1/2

      Fuel level is within range C.

      1/2 to over 1/4

      Fuel level is within range D.

      1/4 to over EMPTY

      Fuel level is within range E.

      EMPTY

    7. Enter the determined position ID into the intelligent tester and press "Next".

      Tip:

      If the position ID has not been entered, "Next" cannot be pressed.

    8. Check the warning light.

      OK

      Condition

      Specified Condition

      The headlight leveling ECU is replaced with a new one.

      Blinks 6 times at 2 Hz → Blinks 3 times at 2 Hz, and then turns off.

      Removal and reinstallation of the headlight leveling ECU, replacement of the rear height control sensor sub-assembly, removal and reinstallation of the rear height control sensor sub-assembly, replacement of the suspension, etc.

      Off → Blinks 3 times at 2 Hz, and then turns off.
      Tip:

      • If the calculated vehicle height is not within the acceptable range, the height control sensor initialization will end as an abnormal termination, and the warning indicator will blink 6 times at 2 Hz continuously. Disconnect the intelligent tester from the DLC3 and turn the ignition switch off. Then restart from "Check Warning Light".

      • If initialization cannot be finished normally, check the LVL terminal circuit (Click here), or perform inspections and repairs according to "Problem Symptoms Table" (Click here)

    9. Press "Exit".

    Result

    Proceed to

    OK

    NG
    OK

    END

    NG

    PERFORM TROUBLESHOOTING

    Click here