DIFFERENTIAL OIL SEAL REPLACEMENT

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front drive shaft oil seal LH and front drive shaft oil seal RH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.

  • VSC disabled or malfunctioning

  • DTCs are output

  • Slip indicator light illuminated

  • ABS warning light illuminated

Click here

PROCEDURE


  1. REMOVE FRONT FENDER APRON SEAL LH

    Click here

  2. DRAIN AUTOMATIC TRANSAXLE FLUID


    1. B0083DW

      Remove the refill plug and gasket from the rear transaxle cover sub-assembly.

    2. B0087D3

      Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle oil pan sub-assembly.

    3. B00867YC01
      *1 No. 1 Transmission Oil Filler Tube

      Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle oil pan sub-assembly.

    4. Drain automatic transaxle fluid from the automatic transaxle assembly.

    5. Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the automatic transaxle oil pan sub-assembly.

      Torque:
      0.8 N*m  { 8 kgf*cm, 7 in.*lbf }

    6. Using a 6 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the automatic transaxle oil pan sub-assembly.

      Tech Tips

      Reuse the old gasket as the overflow plug will be removed again to adjust the automatic transaxle fluid level.

    7. Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage.

      Tech Tips

      Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.

  3. REMOVE FRONT DRIVE SHAFT ASSEMBLY

    Click here

  4. REMOVE DRIVE SHAFT BEARING BRACKET

    Click here

  5. REMOVE FRONT DRIVE SHAFT OIL SEAL LH


    1. B00873ZN01

      Using SST, remove the front drive shaft oil seal LH from the transaxle case sub-assembly.

      SST
      09308-00010

      Note

      Be careful not to damage the transaxle case sub-assembly.

  6. REMOVE FRONT DRIVE SHAFT OIL SEAL RH


    1. B0087VJN01

      Using SST, remove the front drive shaft oil seal RH from the transaxle housing.

      SST
      09308-00010

      Note

      Be careful not to damage the transaxle housing.

  7. INSTALL FRONT DRIVE SHAFT OIL SEAL RH


    1. B00882JC01
      *a Depth

      Using SST and a hammer, install a new front drive shaft oil seal RH to the transaxle housing.

      SST
      09316-60012   ( 09316-00011 )
      Standard Depth
      -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

      Note


      • Make sure that the front drive shaft oil seal RH is installed in the correct direction.

      • Do not damage the lip of the front drive shaft oil seal RH.

  8. INSTALL FRONT DRIVE SHAFT OIL SEAL LH


    1. B0083C4C01
      *a Depth

      Using SST and a hammer, install a new front drive shaft oil seal LH to the transaxle case sub-assembly.

      SST
      09316-10010
      09950-70010   ( 09951-07150 )
      Standard Depth
      -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

      Note


      • Make sure that the front drive shaft oil seal LH is installed in the correct direction.

      • Do not damage the lip of the front drive shaft oil seal LH.

  9. INSTALL DRIVE SHAFT BEARING BRACKET

    Click here

  10. INSTALL FRONT DRIVE SHAFT ASSEMBLY

    Click here

  11. ADJUST AUTOMATIC TRANSAXLE FLUID

    Click here

  12. INSPECT FOR OIL LEAK

  13. INSTALL FRONT FENDER APRON SEAL LH

    Click here