AUTOMATIC TRANSMISSION SYSTEM (for 2KD-FTV), Diagnostic DTC:P2716

DTC Code DTC Name
P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)

DESCRIPTION

A01DXERE01

Shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and vehicle speed sensor. The TCM adjusts the current of shift solenoid valve SLT to control the hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.

DTC Code DTC Detection Condition Trouble Area
P2716 Open or short is detected in the shift solenoid valve SLT circuit for 1 second or more while driving (1-trip detection logic).

  • Open or short in shift solenoid valve SLT circuit

  • Shift solenoid valve SLT

  • TCM

MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLT circuit is detected, the TCM interprets this as a fault. The TCM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

A01DV0QE18

INSPECTION PROCEDURE

PROCEDURE


  1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)


    1. A01DZ3UE04
      Text in Illustration
      *a

      Component without harness connected

      (Transmission Wire)

      Disconnect the transmission wire connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (SLT+) - 6 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
      2 (SLT+) - Body ground Always 10 kΩ or higher
      6 (SLT-) - Body ground Always 10 kΩ or higher

    NG

    INSPECT SHIFT SOLENOID VALVE SLT Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)


    1. A01E22VE33
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to TCM)

      Disconnect the TCM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T19-20 (SLT+) - T19-19 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
      T19-20 (SLT+) - Body ground Always 10 kΩ or higher
      T19-19 (SLT-) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE TCM

  3. INSPECT SHIFT SOLENOID VALVE SLT


    1. A01DWDYE03
      Text in Illustration
      *a

      Component without harness connected

      (Shift Solenoid Valve SLT)

      Remove shift solenoid valve SLT.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 20°C (68°F) 5.0 to 5.6 Ω

    3. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK
      Measurement Condition Specified Condition

      • Battery positive (+) with a 21 W bulb → Terminal 2

      • Battery negative (-) → Terminal 1

      		 Valve moves and makes an operating noise

    NG

    REPLACE SHIFT SOLENOID VALVE SLT

    OK

    REPAIR OR REPLACE TRANSMISSION WIRE