VEHICLE PROXIMITY NOTIFICATION SYSTEM Even when Engine is Started or Transmission Shift Main Switch (P Position Switch) is Pushed, Sound does not Stop

DESCRIPTION

The vehicle approaching speaker controller receives engine oil pressure switch signals from the engine oil pressure switch assembly and P position switch signals from the transmission control ECU assembly, and produces the warning sound from the vehicle approaching speaker assembly.

WIRING DIAGRAM

A005D39E02

PROCEDURE


  1. READ VALUE USING GTS (Oil Pressure SW)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.

    5. Read the Data List according to the display on the GTS.

      Vehicle Proximity Notification System
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Oil Pressure SW Oil pressure switch / OFF or ON

      OFF: Engine started

      ON: Engine not started

      		 -
      Result
      Result Proceed to
      The GTS display changes according to engine operation A
      The GTS display does not change according to engine operation B

    B

    CHECK VEHICLE APPROACHING SPEAKER CONTROLLER Click here

    A

  2. READ VALUE USING GTS (Shift Position)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.

    5. Read the Data List according to the display on the GTS.

      Vehicle Proximity Notification System
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Shift Position P position switch / Not Parking or Parking Not Parking or Parking -
      Result
      Result Proceed to
      The GTS display changes according to the selected shift state A
      The GTS display does not change according to the selected shift state B

    A

    REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER Click here

    B

  3. CHECK VEHICLE APPROACHING SPEAKER CONTROLLER


    1. Disconnect the A23 transmission control ECU assembly connector.

    2. A0059PGE03
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Transmission Control ECU Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A23-20 (IND) - Body ground Power switch on (IG) 8 V or higher
      Power switch off Below 1 V

    NG

    CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - TRANSMISSIONCONTROL ECU ASSEMBLY) Click here

    OK

  4. CHECK TRANSMISSION CONTROL ECU ASSEMBLY


    1. Reconnect the A23 transmission control ECU assembly connector.

    2. A005DY6E01
      Text in Illustration
      *a

      Component with harness connected

      (Transmission Control ECU Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A23-20 (IND) - Body ground Power switch on (IG), park (P) selected Below 2.5 V
      Power switch on (IG), park (P) not selected 8 V or higher

    OK

    REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER Click here

    NG

    REPLACE TRANSMISSION CONTROL ECU ASSEMBLY Click here

  5. CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - TRANSMISSIONCONTROL ECU ASSEMBLY)


    1. Disconnect the L130 vehicle approaching speaker controller connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L130-11 (SFTP) - A23-20 (IND) Always Below 1 Ω
      L130-11 (SFTP) or A23-20 (IND) - Body ground Always 10 kΩ or higher

    OK

    REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. CHECK VEHICLE APPROACHING SPEAKER CONTROLLER


    1. Disconnect the L130 vehicle approaching speaker controller connector.

    2. A005D89E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (Vehicle Approaching Speaker Controller)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      L130-12 (OPSW) - Body ground Idling* 8 V or higher
      Power switch on (IG) Below 1 V

      Tech Tips

      *: Put the engine in inspection mode Click here.


    OK

    REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER Click here

    NG

  7. CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - ENGINE OILPRESSURE SWITCH ASSEMBLY)


    1. Disconnect the D26 engine oil pressure switch assembly connector.

    2. Disconnect the L27 combination meter sub-assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L130-12 (OPSW) - D26-1 Always Below 1 Ω
      L130-12 (OPSW) or D26-1 - Body ground Always 10 kΩ or higher

    OK

    REPLACE ENGINE OIL PRESSURE SWITCH ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR