SPIRAL CABLE(w/o VSC) INSPECTION
PROCEDURE
INSPECT SPIRAL CABLE SUB-ASSEMBLY
Note:As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.
Remove the spiral cable sub-assembly from the vehicle.
Visually check for defects with the spiral cable sub-assembly.
The defects are as follows:
Scratches
Small cracks
Dents
Chips
Cracks or other damage to the connector
OK
No defects are found.
If any defects are found, replace the spiral cable sub-assembly with a new one.
Check the spiral cable sub-assembly.
*a
Component without harness connected
(Spiral Cable Sub-assembly)
-
-
Interlock
-
-
Note:When rotating the spiral cable, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.
Set the spiral cable sub-assembly to the center position.
Measure the resistance between each terminal of the spiral cable sub-assembly according to the table below.
Standard Resistance
Tester Connection
Condition
Specified Condition
E6-1 (CCS) - z4-3 (CCS)
Always
3 Ω or less
E6-2 (ECC) - z4-4 (ECC)
Always
3 Ω or less
E6-2 (ECC) - z1-7 (ECC)
Always
3 Ω or less
E6-3 (EAU) - z1-8 (EAU)
Always
3 Ω or less
E6-4 (AU3) - z1-9 (AU3)
Always
3 Ω or less
E6-5 (AU2) - z1-10 (AU2)
Always
3 Ω or less
E6-6 (AU1) - z1-11 (AU1)
Always
3 Ω or less
E6-7 (SDN) - z1-12 (SDN)
Always
3 Ω or less
E6-9 (HO) - z1-1 (HO)
Always
3 Ω or less
E6-10 (+DP) - z1-2 (+DP)
Always
3 Ω or less
E6-11 (-DP) - z1-3 (-DP)
Always
3 Ω or less
E6-12 (ASL) - z1-4 (ASL)
Always
3 Ω or less
E6-13 (IL+2) - z1-5 (IL+2)
Always
3 Ω or less
E6-14 (SUP) - z1-6 (SUP)
Always
3 Ω or less
E7-1 (D+) - z2-2 (D+)
Always
Below 1 Ω
E7-2 (D-) - z2-1 (D-)
Always
Below 1 Ω
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance as shown in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance as shown in the table below.
Standard Resistance
Tester Connection
Condition
Specified Condition
E6-1 (CCS) - z4-3 (CCS)
Always
3 Ω or less
E6-2 (ECC) - z4-4 (ECC)
Always
3 Ω or less
E6-2 (ECC) - z1-7 (ECC)
Always
3 Ω or less
E6-3 (EAU) - z1-8 (EAU)
Always
3 Ω or less
E6-4 (AU3) - z1-9 (AU3)
Always
3 Ω or less
E6-5 (AU2) - z1-10 (AU2)
Always
3 Ω or less
E6-6 (AU1) - z1-11 (AU1)
Always
3 Ω or less
E6-7 (SDN) - z1-12 (SDN)
Always
3 Ω or less
E6-9 (HO) - z1-1 (HO)
Always
3 Ω or less
E6-10 (+DP) - z1-2 (+DP)
Always
3 Ω or less
E6-11 (-DP) - z1-3 (-DP)
Always
3 Ω or less
E6-12 (ASL) - z1-4 (ASL)
Always
3 Ω or less
E6-13 (IL+2) - z1-5 (IL+2)
Always
3 Ω or less
E6-14 (SUP) - z1-6 (SUP)
Always
3 Ω or less
E7-1 (D+) - z2-2 (D+)
Always
Below 1 Ω
E7-2 (D-) - z2-1 (D-)
Always
Below 1 Ω
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.
Standard Resistance
Tester Connection
Condition
Specified Condition
E6-1 (CCS) - z4-3 (CCS)
Always
3 Ω or less
E6-2 (ECC) - z4-4 (ECC)
Always
3 Ω or less
E6-2 (ECC) - z1-7 (ECC)
Always
3 Ω or less
E6-3 (EAU) - z1-8 (EAU)
Always
3 Ω or less
E6-4 (AU3) - z1-9 (AU3)
Always
3 Ω or less
E6-5 (AU2) - z1-10 (AU2)
Always
3 Ω or less
E6-6 (AU1) - z1-11 (AU1)
Always
3 Ω or less
E6-7 (SDN) - z1-12 (SDN)
Always
3 Ω or less
E6-9 (HO) - z1-1 (HO)
Always
3 Ω or less
E6-10 (+DP) - z1-2 (+DP)
Always
3 Ω or less
E6-11 (-DP) - z1-3 (-DP)
Always
3 Ω or less
E6-12 (ASL) - z1-4 (ASL)
Always
3 Ω or less
E6-13 (IL+2) - z1-5 (IL+2)
Always
3 Ω or less
E6-14 (SUP) - z1-6 (SUP)
Always
3 Ω or less
E7-1 (D+) - z2-2 (D+)
Always
Below 1 Ω
E7-2 (D-) - z2-1 (D-)
Always
Below 1 Ω
If the result is not as specified, replace the spiral cable sub-assembly.