FRONT DOOR DISASSEMBLY

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control)

Click here

Pre-collision system
Memorize steering angle neutral point Parking assist monitor system

Click here

Panoramic View Monitor System

Click here


  • Door window regulator sub-assembly

  • Door glass

  • Door glass run

 Initialize power window control system

  • Auto up and down function

  • Jam protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Catch protection function

  • Window open warning function

Click here

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    Click here

    B0084N2

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    for 2AR-FE:

    Click here

    for A25A-FKS:

    Click here

    for 2GR-FKS:

    Click here

    for 6AR-FSE:

    Click here

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    B0087PP

  3. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH


    1. B00856I

      Disengage the clip and guide to remove the front door lower frame bracket garnish.

  4. REMOVE FRONT DOOR ARMREST COVER SUB-ASSEMBLY


    1. B0083I0

      Using a moulding remover, disengage the 3 claws to remove the front door armrest cover sub-assembly.

  5. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)


    1. B0087HXC01
      B0087TV Protective Tape

      Apply protective tape to the front door trim board sub-assembly as shown in the illustration.

    2. B0085LRC01
      B0089GN Place Hand Here
      B00847Z Remove in this Direction

      Disengage the clip, 7 claws and 5 guides as shown in the illustration.

    3. B008465C01
      B00847Z Remove in this Direction

      Disengage the guide as shown in the illustration.

    4. Disconnect the connector to remove the multiplex network master switch assembly with front door upper armrest base panel.

  6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)


    1. B0084I7C01
      B0087TV Protective Tape

      Apply protective tape to the front door trim board sub-assembly as shown in the illustration.

    2. B0085SCC01
      B0089GN Place Hand Here
      B00847Z Remove in this Direction

      Disengage the clip, 7 claws and 5 guides as shown in the illustration.

    3. B0086SVC01
      B00847Z Remove in this Direction

      Disengage the guide as shown in the illustration.

    4. Disconnect the connector to remove the power window regulator switch assembly with front door upper armrest base panel.

  7. REMOVE FRONT ARMREST ASSEMBLY


    1. B0086H6C01
      B00847Z Remove in this Direction

      Disengage the 3 clips, 8 claws and 3 guides as shown in the illustration.

    2. B0085DDC01
      B00847Z Remove in this Direction

      Disengage the guide to remove the front armrest assembly as shown in the illustration.

  8. REMOVE COURTESY LIGHT ASSEMBLY

    Click here

  9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. B0084FQC01
      B0087TV Protective Tape

      Apply protective tape to the front door panel as shown in the illustration.

    2. B0086KK

      Remove the 3 screws.

    3. B0083ENC01
      B0089GN Place Hand Here
      B00847Z Remove in this Direction

      Disengage the 10 clips as shown in the illustration.

    4. B0086XKC01
      B00847Z Remove in this Direction

      Disengage the 7 claws and guide as shown in the illustration.

    5. B0083PVC01
      *1 Front Door Inside Locking Cable Assembly
      *2 Front Door Lock Remote Control Cable Assembly
      B00847Z Remove in this Direction

      Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly to remove the front door trim board sub-assembly as shown in the illustration.

  10. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP WITH FRONT DOOR VENT SEAL


    1. B0084U5

      Disengage the clip.

    2. B0084YDC01
      B00847Z Remove in this Direction

      Remove the front door inner glass weatherstrip with front door vent seal as shown in the illustration.

  11. REMOVE FRONT DOOR VENT SEAL


    1. B0083NXC01
      B00847Z Remove in this Direction

      Remove the front door vent seal from the front door inner glass weatherstrip as shown in the illustration.

  12. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

    B0087PA

    1. Disengage the 3 claws to remove the front door inside handle sub-assembly.

  13. REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY

    Click here

  14. REMOVE HOLE PLUG

    Click here

  15. REMOVE OUTER MIRROR INSTALL HOLE COVER

    Click here

  16. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER

    Click here

  17. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

    Click here

  18. REMOVE FRONT DOOR SERVICE HOLE COVER


    1. B0085WV

      Disengage the 2 clamps.

    2. B0089LX

      Turn each front door weatherstrip clip 45 degrees and remove the 4 front door weatherstrip clips as shown in the illustration.

    3. B0086VP

      Disengage the 3 clips to remove the front door service hole cover.

  19. REMOVE DOOR SIDE AIRBAG SENSOR

    Click here

  20. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    1. B00845D

      Remove the hole plug.

    2. for Driver Side:


      1. Connect the multiplex network master switch assembly.

    3. for Front Passenger Side:


      1. Connect the power window regulator switch assembly.

    4. Connect the cable to the negative (-) battery terminal.

    5. Turn the ignition switch to ON.

    6. Move the front door glass sub-assembly so that the door glass bolts can be seen.

    7. Turn the ignition switch off.

    8. Disconnect the cable from the negative (-) battery terminal.

    9. for Driver Side:


      1. Disconnect the multiplex network master switch assembly.

    10. for Front Passenger Side:


      1. Disconnect the power window regulator switch assembly.

    11. B0087IN

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the front door glass sub-assembly to fall.

    12. B0087VNC01
      B00847Z Remove in this Direction (1)
      B008776 Remove in this Direction (2)

      Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

      Note

      Do not damage the front door glass sub-assembly.

  21. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY


    1. B0083EX

      Disengage the 2 claws to remove the front door No. 2 service hole cover.

    2. B0083LRC01
      *a Temporary Bolt

      Disconnect the connector.

    3. Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator assembly may fall and cause damage.

    4. Remove the 5 bolts.

    5. Remove the front door window regulator assembly.

    6. Remove the temporary bolt from the front door window regulator assembly.

  22. REMOVE FRONT DOOR PANEL PROTECTOR


    1. B0088W7

      Remove the front door panel protector.

  23. REMOVE FRONT DOOR GLASS RUN


    1. B0089L9

      Remove the front door glass run.

  24. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    1. B0086Q6C01
      B00847Z Remove in this Direction

      Remove the 2 bolts.

    2. Disengage the guide and remove the front door rear lower frame sub-assembly as shown in the illustration.

  25. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY


    1. B0084RN

      Disengage the 2 claws.

    2. Using a screwdriver, disconnect the connector.

    3. B0083RT

      Disengage the 3 clamps.

    4. B0084F4C01
      B00847Z Disengage in this Direction

      Disengage the 2 claws and move the lever as shown in the illustration.

    5. B0083Y9C01
      B00847Z Remove in this Direction

      Remove the front door outside handle assembly as shown in the illustration.

  26. REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)


    1. B0085X6

      Remove the hole plug.

    2. B0087Q8

      Using a T30 "TORX" socket wrench, loosen the screw and remove the front door lock cylinder assembly.

  27. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)


    1. B00890Q

      Remove the hole plug.

    2. B0084N5

      Using a T30 "TORX" socket wrench, loosen the screw.

    3. Disengage the 2 guides and claw and remove the front door outside handle cover.

  28. REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD


    1. B0087D7

      Disengage the 3 claws to remove the front door front outside handle pad.

  29. REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD


    1. B0088OV

      Disengage the 3 guides and claw to remove the front door rear outside handle pad.

  30. REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY

    Click here

  31. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    1. B0083ETC01
      *A Inside
      *B Outside

      Using a T30 "TORX" socket wrench, remove the screw.

    2. Slide the front door outside handle frame sub-assembly as shown in the illustration to disengage the claw and then remove the front door outside handle frame sub-assembly.

  32. REMOVE FRONT DOOR LOCK OPEN ROD


    1. B00859PC01
      B00847Z Remove in this Direction (1)
      B008776 Remove in this Direction (2)

      Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.

  33. REMOVE FRONT DOOR CHECK ASSEMBLY


    1. B00868SC01
      B00888T Nut
      B0086HX Bolt

      Remove the 2 nuts, bolt and front door check assembly.

  34. REMOVE FRONT DOOR WEATHERSTRIP


    1. B00871T

      Using a clip remover, disengage the 25 clips and remove the front door weatherstrip.

  35. REMOVE DOOR FRAME GARNISH


    1. B0084RG

      Disengage the 3 claws to remove the door frame garnish.

  36. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY


    1. B0088ZMC01
      B00847Z Remove in this Direction

      Remove the 2 bolts.

    2. Disengage the guide and remove the front door front lower frame sub-assembly as shown in the illustration.

  37. REMOVE FRONT DOOR PANEL CUSHION


    1. B0083OE

      Disengage the 2 claws to remove the front door panel cushion.

  38. REMOVE FRONT DOOR NO. 2 WEATHERSTRIP


    1. B0085DB

      Disengage the 8 clips to remove the front door No. 2 weatherstrip.

  39. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

    Click here

  40. REMOVE FRONT DOOR FRONT LOWER FRAME UPPER COVER

    Click here

  41. REMOVE DOOR WINDOW FRAME MOULDING CLIP


    1. B0083BQC01
      *a Protective Tape
      B00847Z Remove in this Direction

      Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the door window frame moulding clip.

  42. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING

    Click here

  43. REMOVE FRONT DOOR REAR OUTSIDE SEAL


    1. B008662

      Disengage the guide to remove the front door rear outside seal.

  44. REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING

    Click here

  45. REMOVE FRONT DOOR NO. 2 STRIPE

    Click here

  46. REMOVE FRONT DOOR NO. 3 STRIPE

    Click here