GENERATOR(for 80A Type) REASSEMBLY

PROCEDURE

  1. INSTALL GENERATOR DRIVE END FRAME BEARING

    1. A183132N04

      Using SST and a press, install a new generator drive end frame bearing.

      09950-60010

      09951-00470

      09950-70010

      09951-07100

    2. A153389C11

      *a

      Tab

      *b

      Cutout

      Fit the tabs of the retainer plate into the cutouts of the generator drive end frame to install the retainer plate.

    3. Install the 4 screws.

      2.2 N*m

      22 kgf*cm

      19 in.*lbf

  2. INSTALL GENERATOR ROTOR ASSEMBLY

    1. Place the generator drive end frame on the generator pulley with clutch.

    2. Install the generator rotor assembly to the generator drive end frame.

  3. INSTALL GENERATOR COIL ASSEMBLY

    1. A314531C01

      *a

      Protrusion

      *b

      Groove

      Install a new bearing cover packing.

      Note:

      Align the protrusions of the bearing cover packing with the grooves of the generator coil assembly when installing.

    2. A285303N03

      Using SST and a press, slowly press the generator coil assembly to install it.

      09612-70100

      09612-07240

    3. Install the 4 bolts.

      5.6 N*m

      57 kgf*cm

      50 in.*lbf

  4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

    1. A153827C12

      *a

      Pin (1.0 mm)

      While pushing the 2 brushes into the generator brush holder assembly, insert a 1.0 mm (0.0394 in.) pin into the generator brush holder assembly hole.

    2. A284142C02

      *a

      Pin (1.0 mm)

      Install the generator brush holder assembly to the generator coil assembly with the 2 screws.

      1.8 N*m

      18 kgf*cm

      16 in.*lbf

    3. Pull out the pin from the generator brush holder assembly hole.

  5. INSTALL GENERATOR TERMINAL INSULATOR

    1. Install the generator terminal insulator to the generator coil assembly.

      Note:

      Be sure to install the generator terminal insulator in the correct direction.

  6. INSTALL GENERATOR REAR END COVER

    1. Install the generator rear end cover to the generator coil assembly with the 3 bolts.

      4.6 N*m

      47 kgf*cm

      41 in.*lbf

  7. INSTALL GENERATOR PULLEY WITH CLUTCH

    1. Secure the generator drive end frame in a vise between aluminum plates.

    2. Temporarily install the generator pulley with clutch to the rotor shaft.

    3. A330710C01

      *a

      Rotor Shaft

      Place the rotor shaft end into SST (A).

    4. A330711C01

      *1

      Generator Pulley with Clutch

      Fit SST (B) to the generator pulley with clutch.

    5. A330713C01

      *a

      Turn

      *b

      Hold

      *c

      17 mm Union Nut Wrench

      Using a 17 mm union nut wrench, tighten the generator pulley with clutch by turning SST (B) as shown in the illustration.

      80 N*m

      816 kgf*cm

      59 ft.*lbf

      Note:

      Use the torque value compensation formula to calculate the torque value for use when a torque wrench is combined with a tool such as a union nut wrench.

      Click hereClick here

    6. Remove SST (A) and (B) from the generator pulley with clutch.

    7. Check that the generator pulley with clutch rotates smoothly.

    8. Remove the generator assembly from the vise.

  8. INSTALL GENERATOR PULLEY CAP

    1. Install a new generator pulley cap to the generator pulley with clutch.