HYBRID CONTROL SYSTEM, Diagnostic DTC:P085D-582, P085D-599, P0861-597, P0862-598

DTC Code DTC Name
P085D-582 Gear Shift Control Module "A" Performance
P085D-599 Gear Shift Control Module "A" Performance
P0861-597 Gear Shift Control Module "A" Communication Circuit Low
P0862-598 Gear Shift Control Module "A" Communication Circuit High

DESCRIPTION

When a signal is input from the P position switch (transmission shift main switch) or shift lever, the hybrid vehicle control ECU transmits a P position control (PCON) signal to the transmission control ECU assembly. Based on this signal, the transmission control ECU assembly actuates the shift control actuator assembly in order to mechanically lock or unlock the counter drive gear in the hybrid vehicle transaxle assembly.

P position state (engaged or released) of the actuator assembly is sent to the hybrid vehicle control ECU as a P position (PPOS) signal.

A005ARXE02
DTC No. INF Code DTC Detection Condition Trouble Area
P085D 582 P position (PPOS) signal is logically inconsistent

  • Wire harness or connector

  • Transmission control ECU assembly

  • Hybrid vehicle control ECU
599 P position (PPOS) signal malfunction (output pulse is abnormal)
P0861 597 GND short in P position (PPOS) signal circuit
P0862 598 +B short in P position (PPOS) signal circuit

WIRING DIAGRAM

A005DTVE04
*1 Hybrid Vehicle Control ECU
*2 Transmission Control ECU Assembly
*3 Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

Tech Tips

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


  1. Turn the power switch on (IG) and wait for 10 seconds or more.

  2. Depress the brake pedal, move the shift lever to N, and wait for 10 seconds or more.

  3. Push the transmission shift main switch (P position switch) and wait for 10 seconds or more.

PROCEDURE


  1. CHECK DTC OUTPUT (TRANSMISSION CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Chassis / Transmission Control / Trouble Codes.

    4. Check if DTCs are output.

      Result
      Result Proceed to
      Electronic shift lever system DTCs are not output. A
      Any of the following DTCs are output. B
      DTC No. Relevant Diagnosis
      C2309 Open in B+ Circuit
      C2311 Communication Error from HV ECU

    5. Turn the power switch off.


    B

    GO TO DTC CHART (ELECTRONIC SHIFT LEVER SYSTEM) Click here

    A

  2. CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - TRANSMISSION CONTROL ECU ASSEMBLY)


    1. Disconnect the L5 hybrid vehicle control ECU connector.

    2. Disconnect the A24 transmission control ECU assembly connector.

    3. Disconnect the L197 certification ECU (smart key ECU assembly) connector.

    4. Turn the power switch on (IG).

    5. Measure the voltage according to the value(s) in the table below.

      A005E8DE02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Hybrid Vehicle Control ECU)

      		 *b

      Front view of wire harness connector

      (to Transmission Control ECU Assembly)
      *c Rear view of wire harness connector Certification ECU (Smart Key ECU Assembly) - -
      Standard Voltage
      Tester Connection Condition Specified Condition
      A24-22 (PCON) - Body ground Power switch on (IG) Below 1 V
      A24-23 (PPOS) - Body ground Power switch on (IG) Below 1 V

      Note

      Turning the power switch on (IG) with the hybrid vehicle control ECU connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    6. Turn the power switch off.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      L5-8 (PCON) - A24-22 (PCON) Power switch off Below 1 Ω
      L5-15 (PPOS) - A24-23 (PPOS) Power switch off Below 1 Ω
      A24-23 (PPOS) - L197-25 (PPOS) Power switch off Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      L5-8 (PCON) or A24-22 (PCON) - Body ground and other terminals Power switch off 10 kΩ or higher
      L5-15 (PPOS), A24-23 (PPOS) or L197-25 (PPOS) - Body ground and other terminals Power switch off 10 kΩ or higher

    8. Connect the certification ECU (smart key ECU assembly) connector.

    9. Reconnect the A24 transmission control ECU assembly connector.

    10. Reconnect the L5 hybrid vehicle control ECU connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HYBRID VEHICLE CONTROL ECU (PCON SIGNAL)


    1. Turn the power switch on (IG).

    2. A005D5HE02
      Text in Illustration
      *a

      Component with harness connected

      (Hybrid Vehicle Control ECU)

      Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the table below, and measure the waveform.

      Item Content
      Terminal L5-8 (PCON) - L5-6 (E1)
      Equipment Setting 10V/DIV., 10ms/DIV.
      Condition Power switch on (IG)
      Result
      Result Proceed to
      P position control (PCON) signal waveform appears. A
      P position control (PCON) signal waveform does not appear. B

    3. Turn the power switch off.


    B

    REPLACE HYBRID VEHICLE CONTROL ECU Click here

    A

  4. CHECK HYBRID VEHICLE CONTROL ECU (PPOS SIGNAL)


    1. Turn the power switch on (IG).

    2. A0059URE02
      Text in Illustration
      *a

      Component with harness connected

      (Hybrid vehicle control ECU)

      Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the table below, and measure the waveform.

      Item Content
      Terminal L5-15 (PPOS) - L5-6 (E1)
      Equipment Setting 10V/DIV., 10ms/DIV.
      Condition Power switch on (IG)
      Result
      Result Proceed to
      P position (PPOS) signal waveform appears A
      P position (PPOS) signal waveform does not appear B

    3. Turn the power switch off.


    B

    REPLACE TRANSMISSION CONTROL ECU ASSEMBLY Click here

    A

  5. REPLACE HYBRID VEHICLE CONTROL ECU

    Click here


    NEXT

  6. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Read and record the DTCs and freeze frame data.

    5. Clear DTCs and freeze frame data.

    6. Turn the power switch off.


    NEXT

  7. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG) and leave the vehicle as it is for 10 seconds.

    3. Depress the brake pedal, move the shift lever to N and leave the vehicle as it is for 10 seconds.

    4. Push the P position switch (transmission shift main switch) and leave the vehicle as it is for 10 seconds.

    5. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    6. Check if DTCs are output.

      Result
      Result Proceed to
      No DTCs are output. A
      P085D-582, P085D-599, P0861-597 or P0862-598 is output again. B

    7. Turn the power switch off.


    A

    COMPLETED

    B

    REPLACE TRANSMISSION CONTROL ECU ASSEMBLY Click here