REAR DOOR LOCK INSPECTION

PROCEDURE

1. INSPECT REAR DOOR LOCK ASSEMBLY LH (w/o Double Locking System)

   
   

   1. Check the operation of the door lock motor.

      
      

      1. Apply battery voltage and check the operation of the door lock motor.

         

         *a	UNLOCK	*b	LOCK
         *c	Component without harness connected (Rear Door Lock Assembly LH)	-	-

         OK
         Tester Connection Result K16-4 (L) - Battery positive (+) K16-3 (UL) - Battery negative (-) Lock K16-3 (UL) - Battery positive (+) K16-4 (L) - Battery negative (-) Unlock

         Tech Tips

         If the result is not as specified, replace the rear door lock assembly LH.

   2. Check the resistance of the door lock position switch.

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition K16-9 (LSSR) - K16-10 (E) Locked 10 kΩ or higher K16-9 (LSSR) - K16-10 (E) Unlocked Below 1 Ω

         Tech Tips

         If the result is not as specified, replace the rear door lock assembly LH.

   3. Closer motor operation inspection.

      
      

      1. Set the rear door lock assembly LH to the half latch position.

         

         *a	Half Latch	*b	Full Latch
         *c	Component without harness connected (Rear Door Lock Assembly LH)	-	-

      2. Apply battery voltage and check the operation of the door closer.

         Tester Connection	Result
         K28-1 (CLM+) - Battery positive (+) K28-5 (CLM-) - Battery negative (-)	Moves to full latch position

         Tech Tips

         If the result is not as specified, replace the rear door lock assembly LH.

2. INSPECT REAR DOOR LOCK ASSEMBLY RH (w/o Double Locking System)

   
   

   1. Check the operation of the door lock motor.

      
      

      1. Apply battery voltage and check the operation of the door lock motor.

         

         *a	UNLOCK	*b	LOCK
         *c	Component without harness connected (Rear Door Lock Assembly RH)	-	-

         OK
         Tester Connection Result K2-2 (L) - Battery positive (+) K2-1 (UL) - Battery negative (-) Lock K2-1 (UL) - Battery positive (+) K2-2 (L) - Battery negative (-) Unlock

         Tech Tips

         If the result is not as specified, replace the rear door lock assembly RH.

   2. Check the resistance of the door lock position switch.

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition K2-5 (LSSR) - K2-6 (E) Locked 10 kΩ or higher K2-5 (LSSR) - K2-6 (E) Unlocked Below 1 Ω

         Tech Tips

         If the result is not as specified, replace the rear door lock assembly RH.

   3. Closer motor operation inspection.

      
      

      1. Set the rear door lock assembly RH to the half latch position.

         

         *a	Half Latch	*b	Full Latch
         *c	Component without harness connected (Rear Door Lock Assembly RH)	-	-

      2. Apply battery voltage and check the operation of the door closer.

         Tester Connection	Result
         K14-1 (CLM+) - Battery positive (+) K14-5 (CLM-) - Battery negative (-)	Moves to full latch position

         Tech Tips

         If the result is not as specified, replace the rear door lock assembly RH.

3. INSPECT REAR DOOR LOCK ASSEMBLY LH (w/ Double Locking System)

   
   

   1. Check the operation of the door lock motor.

      
      

      1. Apply battery voltage and check the operation of the door lock motor and double lock motor.

         

         *a	UNLOCK	*b	LOCK
         *c	Component without harness connected (Rear Door Lock Assembly LH)	-	-

         OK
         Tester Connection Result K16-4 (L) - Battery positive (+) K16-3 (UL) - Battery negative (-) Lock K16-3 (UL) - Battery positive (+) K16-4 (L) - Battery negative (-) Unlock K16-2 (DL) - Battery positive (+) K16-1 (UNDL) - Battery negative (-) Set K16-1 (UNDL) - Battery positive (+) K16-2 (DL) - Battery negative (-) Unset

         Tech Tips

         
         

         • Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

         • Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.

         • If the result is not as specified, replace the rear door lock assembly LH.

   2. Check the resistance of the door lock position switch and double lock position switch.

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition K16-9 (LSSR) - K16-10 (E) Locked 10 kΩ or higher K16-9 (LSSR) - K16-10 (E) Unlocked Below 1 Ω K16-5 (DLSR) - K16-6 (E) Unset 10 kΩ or higher K16-5 (DLSR) - K16-6 (E) Set Below 1 Ω

         Tech Tips

         If the result is not as specified, replace the rear door lock assembly LH.

   3. Closer motor operation inspection.

      
      

      1. Set the rear door lock assembly LH to the half latch position.

         

         *a	Half Latch	*b	Full Latch
         *c	Component without harness connected (Rear Door Lock Assembly LH)	-	-

      2. Apply battery voltage and check the operation of the door closer.

         Tester Connection	Result
         K28-1 (CLM+) - Battery positive (+) K28-5 (CLM-) - Battery negative (-)	Moves to full latch position

         Tech Tips

         If the result is not as specified, replace the rear door lock assembly LH.

4. INSPECT REAR DOOR LOCK ASSEMBLY RH (w/ Double Locking System)

   
   

   1. Check the operation of the door lock motor.

      
      

      1. Apply battery voltage and check the operation of the door lock motor and double lock motor.

         

         *a	UNLOCK	*b	LOCK
         *c	Component without harness connected (Rear Door Lock Assembly RH)	-	-

         OK
         Tester Connection Result K2-2 (L) - Battery positive (+) K2-1 (UL) - Battery negative (-) Lock K2-1 (UL) - Battery positive (+) K2-2 (L) - Battery negative (-) Unlock K2-4 (DL) - Battery positive (+) K2-3 (UNDL) - Battery negative (-) Set K2-3 (UNDL) - Battery positive (+) K2-4 (DL) - Battery negative (-) Unset

         Tech Tips

         
         

         • Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

         • Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.

         • If the result is not as specified, replace the rear door lock assembly RH.

   2. Check the resistance of the door lock position switch.

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition K2-5 (LSSR) - K2-6 (E) Locked 10 kΩ or higher K2-5 (LSSR) - K2-6 (E) Unlocked Below 1 Ω K2-9 (DLSR) - K2-10 (E) Unset 10 kΩ or higher K2-9 (DLSR) - K2-10 (E) Set Below 1 Ω

         Tech Tips

         If the result is not as specified, replace the rear door lock assembly RH.

   3. Closer motor operation inspection.

      
      

      1. Set the rear door lock assembly RH to the half latch position.

         

         *a	Half Latch	*b	Full Latch
         *c	Component without harness connected (Rear Door Lock Assembly RH)	-	-

      2. Apply battery voltage and check the operation of the door closer.

         Tester Connection	Result
         K14-1 (CLM+) - Battery positive (+) K14-5 (CLM-) - Battery negative (-)	Moves to full latch position

         Tech Tips

         If the result is not as specified, replace the rear door lock assembly RH.