POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Driver Door Window Only) Rear Power Window RH does not Operate with Rear Power Window Switch RH

DTC Code DTC Name
Rear Power Window RH does not Operate with Rear Power Window Switch RH

DESCRIPTION

When the ignition switch is ON, the rear door window regulator assembly (for RH door) is operated by the rear power window regulator switch assembly (for RH door).

WIRING DIAGRAM

B301257E16

CAUTION / NOTICE / HINT

Note:

  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • Check that the window lock switch is off before performing the following procedure.

PROCEDURE

  1. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR RH DOOR) - BATTERY)

    1. Disconnect the J5 rear power window regulator switch assembly (for RH door) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      J5-3 (B) - Body ground

      Ignition switch ON

      11 to 14 V

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR RH DOOR)

    1. B164433C02

      *a

      Component without harness connected

      (Rear Power Window Regulator Switch Assembly (for RH Door))

      Remove the rear power window regulator switch assembly (for RH door).

      Click here

    2. Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      1 (D) - 2 (SD)

      UP

      Below 1 Ω

      3 (B) - 4 (U)

      Below 1 Ω

      1 (D) - 2 (SD)

      Off

      Below 1 Ω

      4 (U) - 5 (SU)

      Below 1 Ω

      4 (U) - 5 (SU)

      DOWN

      Below 1 Ω

      1 (D) - 3 (B)

      Below 1 Ω

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR RH DOOR)

    Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR RH DOOR) - REAR DOOR WINDOW REGULATOR ASSEMBLY (FOR RH DOOR))

    1. Disconnect J6 the rear door window regulator assembly (for RH door) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      J5-4 (U) - J6-1 (U)

      Always

      Below 1 Ω

      J5-1 (D) - J6-2 (D)

      Always

      Below 1 Ω

      J5-4 (U) - Body ground

      Always

      10 kΩ or higher

      J5-1 (D) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

    1. B164359C15

      *A

      for LHD

      *B

      for RHD

      *a

      Component without harness connected

      (Power Window Regulator Master Switch Assembly)

      Remove the power window regulator master switch assembly.

      Click here

    2. Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard Resistance

      Table 1. for LHD

      Tester Connection

      Condition

      Specified Condition

      6 (B) - 10 (U)

      UP

      Below 1 Ω

      1 (E) - 18 (D)

      Below 1 Ω

      1 (E) - 10 (U)

      Off

      Below 1 Ω

      1 (E) - 18 (D)

      Below 1 Ω

      6 (B) - 18 (D)

      DOWN

      Below 1 Ω

      1 (E) - 10 (U)

      Below 1 Ω
      Table 2. for RHD

      Tester Connection

      Condition

      Specified Condition

      6 (B) - 16 (U)

      UP

      Below 1 Ω

      9 (E) - 15 (D)

      Below 1 Ω

      9 (E) - 16 (U)

      Off

      Below 1 Ω

      9 (E) - 15 (D)

      Below 1 Ω

      6 (B) - 15 (D)

      DOWN

      Below 1 Ω

      9 (E) - 16 (U)

      Below 1 Ω

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

    Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR RH DOOR)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Table 3. for LHD

      Tester Connection

      Condition

      Specified Condition

      H11-10 (U) - J5-5 (SU)

      Always

      Below 1 Ω

      H11-18 (D) - J5-2 (SD)

      Always

      Below 1 Ω

      H11-10 (U) - Body ground

      Always

      10 kΩ or higher

      H11-18 (D) - Body ground

      Always

      10 kΩ or higher
      Table 4. for RHD

      Tester Connection

      Condition

      Specified Condition

      G11-16 (U) - J5-5 (SU)

      Always

      Below 1 Ω

      G11-15 (D) - J5-2 (SD)

      Always

      Below 1 Ω

      G11-16 (U) - Body ground

      Always

      10 kΩ or higher

      G11-15 (D) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE REAR DOOR WINDOW REGULATOR ASSEMBLY (FOR RH DOOR)

    except Sedan:Click here

    for Sedan:Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR