AUDIO AND VISUAL SYSTEM(for Sedan Radio and Display Type) OPERATION CHECK

  1. CHECK PANEL & STEERING SWITCH

    Tip:

    • The radio and display receiver assembly panel switches and steering switches are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

    1. Enter diagnostic mode.

      Click here

    2. E268454

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. E268513

      Select "Panel & Steering Switch" from the "Function Check/Setting I" screen.

    4. E225786N01

      Panel & Steering Switch Check Mode

      Table 1. Screen Description

      Display

      Content

      *a: Switch condition

      "Pushed" is displayed when any switch is pushed.

      *b: Number of switches pushed

      • Number of switches pushed at once is displayed.

      • If more than 3 switches are pushed at once, "More than 3" is displayed.

      • If 4 or more switches are pushed at once, "More than 3" is displayed

      *c: Rotary switch direction

      Direction of rotary switch is displayed.

      1. Operate each switch and check that the switch conditions are correctly displayed.

        Note:

        When the "SETUP" or " MENU" switch is pressed and held for 3 seconds or more, diagnostic mode will be canceled.

  2. CHECK TOUCH SWITCH

    Tip:

    • The touch switches on the screen are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

    1. Enter diagnostic mode.

      Click here

    2. E268454

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. E268514

      Select "Touch Switch" from the "Function Check/Setting I" screen.

    4. E176521

      Touch Switch Check

      1. Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

        Tip:

        • A "+" mark is displayed where the display is touched.

        • The "+" mark remains on the display even after your finger is removed.

  3. CHECK MICROPHONE

    Tip:

    • The microphone and microphone input level are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

    1. Enter diagnostic mode.

      Click here

    2. E268454

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. E268515

      Select "Microphone Check" from the "Function Check/Setting I" screen.

    4. E277821N01

      Microphone Check

      Table 2. Screen Description

      Display

      Content

      *a: Microphone input level meter

      Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.

      1. When speaking into the microphone, check that the microphone input level meter changes according to the input level.

        Tip:

        The microphone is active at all times when this screen is displayed.

  4. CHECK VEHICLE SIGNAL

    Tip:

    • Vehicle signals received by the radio and display receiver assembly are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

    1. Enter diagnostic mode.

      Click here

    2. E268454

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. E268516

      Select "Vehicle Signal" from the "Function Check/Setting I" screen.

    4. E225776

      Vehicle Signal Check Mode

      Table 3. Screen Description

      Display

      Content

      Battery

      Battery voltage is displayed.

      IG

      Ignition switch ON/OFF state is displayed.

      PKB

      Parking brake ON/OFF state is displayed.

      REV

      Reverse signal ON/OFF state is displayed.

      SPEED

      Vehicle speed is displayed in km/h.

      TAIL

      Tail signal (light control switch) ON/OFF state is displayed.

      ADIM/TCAN

      Brightness state DIM (with)/BRIGHT (without) is displayed.
      Tip:

      • Only items sending vehicle signals will be displayed.

      • This screen displays vehicle signals input to the radio and display receiver assembly.

      • This screen is updated once per second.

      1. When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.

  5. CHECK HANDS-FREE VOICE QUALITY SETTING

    Tip:

    • The hands-free voice quality of a "Bluetooth" compatible phone can be adjusted using the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

    1. Enter diagnostic mode.

      Click here

    2. E268454

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. E268517

      Select "HF Voice Quality Setting" from the "Function Check/Setting I" screen.

    4. E268475C01

      *a

      Numeric Keypad

      *b

      Setting Button

      *c

      Reset Button

      Hands-Free Voice Quality Setting

      1. If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.

      2. When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.

        Table 4. Settings

        Parameter

        Target Phenomenon

        Voice Quality Type

        Positive Effect of Changing Voice Quality

        Negative Effect of Changing Voice Quality

        A

        (Noise)

        The other party hears background noise when listening to your voice.

        1000

        The amount of background noise the other party hears when listening to your voice is reduced.

        The volume of voice the other party hears when listening to your voice may temporarily drop.

        B

        (Noise)

        The other party hears a lot of background noise when listening to your voice.

        2000

        The amount of background noise the other party hears when listening to your voice is sharply reduced.

        The volume of voice the other party hears when listening to your voice may temporarily drop.

        C

        (Echo)

        The other party hears weak echoes.

        0100

        The amount of echo is reduced (low level).

        Sound quality of the other party deteriorates (low level).

        D

        (Echo)

        The other party hears strong echoes.

        0200

        The amount of echo is reduced (high level).

        Sound quality of the other party deteriorates (high level).
        Table 5. Settings (When Multiple Phenomenon Occurred)

        Parameter

        Target Phenomenon

        Voice Quality Type

        Positive Effect of Changing Voice Quality

        Negative Effect of Changing Voice Quality

        A+C

        The other party hears background noise and weak echoes when listening to your voice.

        1100

        • The amount of background noise the other party hears when listening to your voice is reduced.

        • The amount of echo is reduced (low level).

        • The volume of voice may drop temporarily.

        • Sound quality of the other party deteriorates (low level).

        A+D

        The other party hears background noise and strong echoes when listening to your voice.

        1200

        • The amount of background noise the other party hears when listening to your voice is reduced.

        • The amount of echo is reduced (high level).

        • The volume of voice may drop temporarily.

        • Sound quality of the other party deteriorates (high level).

        B+C

        The other party hears a lot of background noise and weak echoes when listening to your voice.

        2100

        • The amount of background noise the other party hears when listening to your voice is sharply reduced.

        • The amount of echo is reduced (low level).

        • The volume of voice may drop temporarily.

        • Sound quality of the other party deteriorates (low level).

        B+D

        The other party hears a lot of background noise and strong echoes when listening to your voice.

        2200

        • The amount of background noise the other party hears when listening to your voice is sharply reduced.

        • The amount of echo is reduced (high level).

        • The volume of voice may drop temporarily.

        • Sound quality of the other party deteriorates (high level).
        Tip:

        • The default value is "0000".

        • Settings will be applied when the setting button is selected.

        • If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.

        • If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by pressing the "INIT" switch.

  6. CHECK SPEAKER

    Tip:

    • This function is used when checking the speaker wiring and whether the speakers are functioning properly.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

    1. Turn audio mode on and play any audio source.

      Tip:

      This audio source will be used for the speaker check.

    2. Enter diagnostic mode.

      Click here

    3. E268484

      Select "Failure Diagnosis" from the "Service Menu" screen.

    4. E268489

      Select "System Check" from the "Failure Diagnosis" screen.

    5. E268474

      Select "SP Check ON" from the "System Check Mode" screen.

    6. Check the speaker wiring and check that the speakers are functioning properly.

      Tip:

      • Check that each speaker outputs sound from the selected audio source properly.

      • "SP Check OFF" is displayed during the speaker check.

      • Sound can be heard from the speakers around the vehicle in order beginning from a speaker on the front side.

      • More than one speaker may sound simultaneously depending on the speaker wiring.

    7. Sound stops when any of the following conditions are met:

      1. The "SP Check OFF" switch is pressed.

      2. The ignition switch is turned off.

      3. Diagnostic mode is turned off.

      4. The screen is changed to another screen.

      5. Audio mode is turned off.

  7. CHECK SOFTWARE ERROR HISTORY

    Tip:

    This function is used to check the cause when the radio and display receiver assembly screen is blacked out.

    1. Check Software Error History.

      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON.

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Software Error History.

        Body Electrical > Navigation System > Utility

        Tester Display

        Software Error History

      5. When an item is stored for Software Error History, record it before repairing the radio and display receiver assembly.

        Table 6. Software Error History Screen Description

        Error Description

        Trigger

        Detail

        Software Reset

        Navi Microcomputer

        Hexadecimal Number

        Audio Microcomputer

        CAN Microcomputer

        No Video Signal

        Front Monitor

        Rear Monitor

        MOST Cold Restart

        Always
        Tip:

        • Software Error History can store up to 5 history data items. If a new software error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.

        • If an error that is unsupported by the GTS occurs, a "-" is displayed for the display items.

    2. Clear software error history.

      1. When DTCs are cleared using any of the following operations, Software Error History will be cleared as well.

        Click here

        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.

  8. CHECK OPTICAL DISC ERROR HISTORY

    Tip:

    This function is used to check the cause of an optical disc error.

    1. Check Optical Disc Error History.

      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON.

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Optical Disc Error History.

        Body Electrical > Navigation System > Utility

        Tester Display

        Optical Disc Error History

      5. When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.

        Table 7. Optical Disc Error History Screen Description

        Display

        Content

        Error Type

        Displays the type of error.

        Device

        Displays the malfunctioning device.

        Date

        Displays the date and time that the malfunction occurred.
        Table 8. "Error Type" Screen Description

        Error Type

        Detection Condition

        Action

        Read Error

        When a disc read error occurs.

        Proceed to next suspected area shown in Problem Symptoms Table.

        Click here

        Disc damaged/upside down/dirty

        When it is determined that any of the following is the cause of the disc read error:

        • The disc cannot be read.

        • The disc cannot be read because of dirt or scratches.

        • The disc cannot be read because it is inserted upside down.

        Cannot determine disc type

        An unsuitable disc is inserted.

        DPS error

        When an error occurs while decoding MP3/WMA/AAC files.

        Some files are corrupt

        • When MP3/WMA/AAC files cannot be played back because they are unsupported.

        • Even though the file extensions are MP3, WMA or AAC files cannot be played back because the header information cannot be read.

        Some files cannot be found

        • When a disc without music data is played back.

        • When there are no playable MP3/WMA/AAC files.

        Copy protection violation

        When a file with copyright protection that cannot be played back is played back.
        Table 9. "Device" Screen Description

        Device

        Component

        DVD-P

        Radio and display receiver assembly*1

        CD-P

        Radio and display receiver assembly*2

        R-Seat DVD-P

        Not available

        *1: w/ DVD Player

        *2: w/o DVD Player

        Tip:

        • Optical Disc Error History can store up to 7 history data items. If a new optical disc error occurs when 7 data items have already been stored, the oldest data is cleared and the new data is stored.

        • If an error that is unsupported by the GTS occurs, a "-" or blank is displayed for the display items.

    2. Clear optical disc error history.

      1. When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well.

        Click here

        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.

  9. Tip:

    • This function is used to detect disconnection of the video devices.

    • In order to inspect the RSE, a disc should be inserted into the radio and display receiver assembly.

    CHECK VIDEO DEVICE CONNECTION CHECK

    1. Check Video Device Connection Check.

      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON.

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Video Device Connection Check.

        Body Electrical > Navigation System > Utility

        Tester Display

        Video Device Connection Check

      5. When an item is stored for Video Device Connection Check, record it before proceeding with troubleshooting.

        Tip:

        • DTCs are stored when errors are detected.

        • Depending on the vehicle, some of the items are not displayed on the "Error Detected Image Line (Type)" screen.

        Table 10. Video Device Connection Check Screen Description

        Error Detected Image Line (Type)

        Areas to be Checked

        H/U - > Separate Display (GVIF)

        Not available

        H/U - > Full RSE (GVIF)

        Not available

        RSE - > Seat Back Display RH (GVIF)

        Not available

        RSE - > Seat Back Display LH (GVIF)

        Not available

        Rear Camera - > H/U (NTSC)

        NTSC video signal between the radio and display receiver assembly and rear television camera assembly

        IPA/BGM/PVM ECU - > Separate Display (GVIF)

        Not available

        IPA/BGM/PVM ECU - > H/U (NTSC)

        Not available

        IPA/BGM/PVM ECU - > H/U (GVIF)

        Not available

    2. Clear video device connection check.

      1. When DTCs are cleared using any of the following operations, Video Device Connection Check will be cleared as well.

        Click here

        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.

  10. Tip:

    This function is used to check the connection history when the connection between the radio and display receiver assembly and a "Bluetooth" device is unstable.

    CHECK "Bluetooth" CONNECTION HISTORY

    1. Check "Bluetooth" Connection History.

      Tip:

      • "Bluetooth" Connection History displays data stored in the internal memory of the ECU, such as the date a "Bluetooth" connection was attempted and the progress of a "Bluetooth" connection.

      • By checking "Bluetooth" Connection History, the date, cause, etc. of a "Bluetooth" device failing to register or connect can be analyzed.

      • "Bluetooth" connection history indicates the estimated cause of a malfunction, but does not determine it. Therefore, checking "Bluetooth" Connection History may not improve the problem.

      • Performing inspection using the GTS before recording the "Bluetooth" Connection History may clear the operation history.

      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON.

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / "Bluetooth" Connection History.

        Body Electrical > Navigation System > Utility

        Tester Display

        Bluetooth Connection History

      5. When an item is stored for "Bluetooth" Connection History, record it before proceeding with troubleshooting.

        Table 11. "Bluetooth" Connection History Screen Description

        Item

        Content

        Occurrence Start Date/Time

        Date and time of "Bluetooth" connection are displayed.

        Occurrence End Date/Time

        Date and time of "Bluetooth" disconnection are displayed.

        History Type

        Type of "Bluetooth" Connection History is displayed.

        Result

        "Bluetooth" connection result is displayed.

        Contents

        "Bluetooth" connection status is displayed.

        "Bluetooth" Address

        "Bluetooth" device address is displayed.

        Continuance Time

        The number of retries when "Bluetooth" connection was performed is displayed.
        Table 12. History Type: ACC ON

        Result

        Contents

        Detail

        Areas to be Checked

        -

        -

        Ignition switch ACC

        -
        Table 13. History Type: Registration

        Result

        Contents

        Detail

        Areas to be Checked

        Success (HFP)

        No Error

        "Bluetooth" device was registered as a hands-free device properly.

        -

        Success (AVP)

        No Error

        "Bluetooth" device was registered as a "Bluetooth" audio device properly.

        -

        Failure

        Time Out

        Could not perform "Bluetooth" connection properly.

        • Check that the "Bluetooth" device is in the cabin.

        • Check that the "Bluetooth" device is not connected to another device using the "Bluetooth" connection.

        • Restart the "Bluetooth" device and operate it again.

        Authentication Error

        Wrong PIN code was input for PIN code verification.

        Perform "Bluetooth" device registration again. (Input PIN code correctly.)

        Did not select the confirmation button even though a passkey was displayed.

        Perform "Bluetooth" device registration again. (When a passkey is displayed, select the confirmation button.)

        A verification error occurred between the radio and display receiver assembly and "Bluetooth" device.

        Restart the radio and display receiver assembly and "Bluetooth" device, and operate them again.

        ACL Link Disconnection

        "Bluetooth" connection was disconnected by operating the "Bluetooth" device.

        Perform "Bluetooth" device registration again.

        "Bluetooth" connection could not be established due to wave interference around the vehicle.

        Check for wave interference and perform "Bluetooth" device registration again.

        "Bluetooth" device was outside the communication area.

        Bring the "Bluetooth" device near the radio and display receiver assembly and perform "Bluetooth" device registration again.

        "Bluetooth" setting on the "Bluetooth" device was off.

        Change the "Bluetooth" setting to on and perform "Bluetooth" device registration again.

        "Bluetooth" device was off.

        Turn the "Bluetooth" device on and perform "Bluetooth" device registration again.

        A malfunction occurred in the "Bluetooth" device.

        Restart the "Bluetooth" device and operate it again.

        Memory Write Failure

        "Bluetooth" device information could not be stored in the radio and display receiver assembly.

        Perform "Bluetooth" device registration again.

        Other Error

        An error other than above occurred.

        After turning the ignition switch off and back to ON again, perform "Bluetooth" device registration again.

        Cancel

        No Error

        Registration was suspended by operating the radio and display receiver assembly or "Bluetooth" device.

        -
        Table 14. History Type: Connection

        Result

        Contents

        Detail

        Areas to be Checked

        • Auto Connect Success (HFP)

        • Manual Connect Success (HFP)

        No Error

        "Bluetooth" device was connected as a hands-free device properly.

        -

        • Auto Connect Failure (HFP)

        • Manual Connect Failure (HFP)

        Time Out

        Could not perform "Bluetooth" connection properly.

        • Check that the "Bluetooth" device is in the cabin.

        • Check that the "Bluetooth" device is not connected to another device using the "Bluetooth" connection.

        • Restart the "Bluetooth" device and operate it again.

        Authentication Error

        Verification of authentication key between the radio and display receiver assembly and "Bluetooth" device failed.

        If "Bluetooth" connection failed again even though the "Bluetooth" connection was performed, perform registration again.

        A verification error occurred between the radio and display receiver assembly and "Bluetooth" device.

        Restart the radio and display receiver assembly and "Bluetooth" device, and operate them again.

        Page Time Out

        Could not find a "Bluetooth" device near the radio and display receiver assembly.

        Bring the "Bluetooth" device near the radio and display receiver assembly and perform "Bluetooth" connection again.

        "Bluetooth" connection could not be established due to wave interference around the vehicle.

        Check for wave interference and perform "Bluetooth" connection again.

        "Bluetooth" device was outside the communication area.

        Bring the "Bluetooth" device near the radio and display receiver assembly and perform "Bluetooth" connection again.

        "Bluetooth" setting on the "Bluetooth" device was off.

        Change the "Bluetooth" setting to on and perform "Bluetooth" connection again.

        "Bluetooth" device was off.

        Turn the "Bluetooth" device on and perform "Bluetooth" connection again.

        A malfunction occurred in the "Bluetooth" device.

        Restart the "Bluetooth" device and operate it again.
        Table 15. History Type: Connection

        Result

        Contents

        Detail

        Areas to be Checked

        • Auto Connect Failure (HFP)

        • Manual Connect Failure (HFP)

        ACL Link Disconnection

        "Bluetooth" connection was disconnected by operating the "Bluetooth" device.

        Perform "Bluetooth" connection again.

        "Bluetooth" connection could not be established due to wave interference around the vehicle.

        Check for wave interference and perform "Bluetooth" connection again.

        "Bluetooth" device was outside the communication area.

        Bring the "Bluetooth" device near the radio and display receiver assembly and perform "Bluetooth" connection again.

        "Bluetooth" setting on the "Bluetooth" device was off.

        Change the "Bluetooth" setting to on and perform "Bluetooth" connection again.

        "Bluetooth" device was off.

        Turn the "Bluetooth" device on and perform "Bluetooth" connection again.

        A malfunction occurred in the "Bluetooth" device.

        Restart the "Bluetooth" device and operate it again.

        SDP Error

        HFP was disabled on the "Bluetooth" device.

        Enable HFP on the "Bluetooth" device and perform "Bluetooth" connection again.

        "Bluetooth" device which operation had not been confirmed was used.

        Check that the "Bluetooth" device is hands-free compatible and its operation has been confirmed.

        Click here

        Other Error

        An error other than above occurred.

        After turning the ignition switch off and back to ON again, perform "Bluetooth" device registration again.

        Manual Connect Cancel (HFP)

        No Error

        Connection was interrupted by operating the radio and display receiver assembly or "Bluetooth" device.

        -
        Table 16. History Type: Connection

        Result

        Contents

        Detail

        Areas to be Checked

        • Auto Connect Success (AVP)

        • Manual Connect Success (AVP)

        No Error

        "Bluetooth" device was connected as a "Bluetooth" audio device properly.

        -

        • Auto Connect Failure (AVP)

        • Manual Connect Failure (AVP)

        Time Out

        Could not perform "Bluetooth" connection properly.

        • Check that the "Bluetooth" device is in the cabin.

        • Check that the "Bluetooth" device is not connected to another device using the "Bluetooth" connection.

        • Restart the "Bluetooth" device and operate it again.

        Authentication Error

        Verification of authentication key between the radio and display receiver assembly and "Bluetooth" device failed.

        If "Bluetooth" connection failed again even though the "Bluetooth" connection was performed, perform registration again.

        A verification error occurred between the radio and display receiver assembly and "Bluetooth" device.

        Restart the radio and display receiver assembly and "Bluetooth" device, and operate them again.

        Page Time Out

        Could not find a "Bluetooth" device near the radio and display receiver assembly.

        Bring the "Bluetooth" device near the radio and display receiver assembly and perform "Bluetooth" connection again.

        "Bluetooth" connection could not be established due to wave interference around the vehicle.

        Check for wave interference and perform "Bluetooth" connection again.

        "Bluetooth" device was outside the communication area.

        Bring the "Bluetooth" device near the radio and display receiver assembly and perform "Bluetooth" connection again.

        "Bluetooth" setting on the "Bluetooth" device was off.

        Change the "Bluetooth" setting to on and perform "Bluetooth" connection again.

        "Bluetooth" device was off.

        Turn the "Bluetooth" device on and perform "Bluetooth" connection again.

        A malfunction occurred in the "Bluetooth" device.

        Restart the "Bluetooth" device and operate it again.
        Table 17. History Type: Connection

        Result

        Contents

        Detail

        Areas to be Checked

        • Auto Connect Failure (AVP)

        • Manual Connect Failure (AVP)

        ACL Link Disconnection

        "Bluetooth" connection was disconnected by operating the "Bluetooth" device.

        Perform "Bluetooth" connection again.

        "Bluetooth" connection could not be established due to wave interference around the vehicle.

        Check for wave interference and perform "Bluetooth" connection again.

        "Bluetooth" device was outside the communication area.

        Bring the "Bluetooth" device near the radio and display receiver assembly and perform "Bluetooth" connection again.

        "Bluetooth" setting on the "Bluetooth" device was off.

        Change the "Bluetooth" setting to on and perform "Bluetooth" connection again.

        "Bluetooth" device was off.

        Turn the "Bluetooth" device on and perform "Bluetooth" connection again.

        A malfunction occurred in the "Bluetooth" device.

        Restart the "Bluetooth" device and operate it again.

        SDP Error

        AVP was disabled on the "Bluetooth" device.

        Enable AVP on the "Bluetooth" device and perform "Bluetooth" connection again.

        "Bluetooth" device which operation had not been confirmed was used.

        Check that the "Bluetooth" device is "Bluetooth" audio compatible and its operation has been confirmed.

        Click here

        Other Error

        An error other than above occurred.

        After turning the ignition switch off and back to ON again, perform "Bluetooth" device registration again.

        Manual Connect Cancel (AVP)

        No Error

        Connection was interrupted by operating the radio and display receiver assembly or "Bluetooth" device.

        -
        Table 18. History Type: Disconnection

        Result

        Contents

        Detail

        Areas to be Checked

        Disconnection Complete (HFP)

        Link Loss

        The "Bluetooth" device was moved outside of the communication area.

        Move the "Bluetooth" device into the communication area.

        "Bluetooth" connection was disconnected due to wave interference around the vehicle.

        Check for wave interference and perform "Bluetooth" connection again.

        A malfunction occurred in the "Bluetooth" device.

        Restart the "Bluetooth" device and operate it again.

        Disconnection from Partner

        "Bluetooth" connection was disconnected by operating the "Bluetooth" device.

        -

        Disconnection from Self

        "Bluetooth" connection was disconnected by operating the radio and display receiver assembly.

        -

        Other Error

        An error other than above occurred.

        After turning the ignition switch off and back to ON again, perform "Bluetooth" device registration again.

        Disconnection Complete (AVP)

        Link Loss

        The "Bluetooth" device was moved outside of the communication area.

        Move the "Bluetooth" device into the communication area.

        "Bluetooth" connection was disconnected due to wave interference around the vehicle.

        Check for wave interference and perform "Bluetooth" connection again.

        A malfunction occurred in the "Bluetooth" device.

        Restart the "Bluetooth" device and operate it again.

        Disconnection from Partner

        "Bluetooth" connection was disconnected by operating the "Bluetooth" device.

        -

        Disconnection from Self

        "Bluetooth" connection was disconnected by operating the radio and display receiver assembly.

        -

        Other Error

        An error other than above occurred.

        After turning the ignition switch off and back to ON again, perform "Bluetooth" device registration again.
        Table 19. History Type: Send

        Result

        Contents

        Detail

        Areas to be Checked

        Success

        No Error

        Call was made properly.

        -

        Failure

        Out of Service

        Outside the cellular phone service area.

        Move the vehicle into a cellular phone service area, check that the "Bluetooth" device is connected to the vehicle and operate the device again.

        Redial Regulation

        Redial of the "Bluetooth" device was restricted and could not make a hands-free call.

        Restart the "Bluetooth" device and operate it again.

        Other Error

        Could not make a hands-free call due to a "Bluetooth" device malfunction.

        Restart the "Bluetooth" device and operate it again.

        Could not make a hands-free call due to a radio and display receiver assembly malfunction.

        After turning the ignition switch off and back to ON again, perform "Bluetooth" device registration again.

        Could not make a hands-free call from the radio and display receiver assembly because the call status of the "Bluetooth" device was not transmitted to the radio and display receiver assembly.

        Restart the "Bluetooth" device and operate it again.

    2. Clear "Bluetooth" connection history.

      1. When DTCs are cleared using any of the following operations, "Bluetooth" Connection History will be cleared as well.

        Click here

        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.