FRONT SEAT OUTER BELT ASSEMBLY(for Double Cab) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front seat outer belt assembly LH removal / installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Pre-collision system

Click here

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedures listed below are for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    B0069A2

    for Type A:

    Click here

    for Type B:

    Click here

    for Type C:

    Click here

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    B00693Q

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  4. REMOVE REAR DOOR SCUFF PLATE LH

    Click here

  5. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH (Floor Anchor)


    1. B0025VZ

      Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly LH.

  6. REMOVE LOWER CENTER PILLAR GARNISH LH

    Click here

  7. REMOVE PILLAR ASSIST GRIP ASSEMBLY

    Click here

  8. REMOVE SEAT BELT ANCHOR COVER CAP

    Click here

  9. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH


    1. B0027NZ

      Remove the nut and disconnect the shoulder anchor of the front seat outer belt assembly LH.

    2. B0025CGC01
      *1 Locking Button
      B00692L Protective Tape

      w/ Pretensioner:


      1. Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector as shown in the illustration.

        Tech Tips

        Tape the screwdriver tip before use.

      2. B0027V3

        Remove the bolt.

      3. Detach the 2 guides and remove the front seat outer belt assembly LH.

    3. B0028YD

      w/o Pretensioner:


      1. Remove the bolt.

      2. Detach the 2 guides and remove the front seat outer belt assembly LH.

  10. REMOVE UPPER CENTER PILLAR GARNISH LH

    Click here

  11. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    Tech Tips

    Perform this procedure when replacing the shoulder belt anchor cover LH.


    1. B0028MSC01
      B0069FO Remove in this Direction

      Detach the claw and remove the front shoulder belt anchor plate sub-assembly LH in the illustration.

  12. REMOVE SHOULDER BELT ANCHOR COVER LH

    Tech Tips

    Perform this procedure when replacing the shoulder belt anchor cover LH.


    1. B00273KC01
      *1 Shoulder Belt Anchor Cover LH

      Detach the claw and remove the 2 shoulder belt anchor cover RH.

  13. REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY


    1. B0025YW

      Remove the 2 bolts.

    2. Detach the guide to remove the front shoulder belt anchor adjuster assembly.