SFI SYSTEM(w/o Canister Pump Module) FAIL-SAFE CHART

If any of the following DTCs are stored, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily or stops fuel injection.

DTC Code	Component	Fail-Safe Operation	Fail-Safe Deactivation Condition
P001001 P001100 P001200 P002001 P002100 P002200 P102301 P136001 P136101 P136201 P136301 P261401	Cam timing control motor with EDU assembly	The cam timing control motor with EDU assembly is operated to the most retarded position. Boost prohibited. Idle up (control of combustion worsening).	Pass condition detected and then engine switch turned off
P001500 P002500	VVT system	Exhaust VVT maximum advance contact. Boost prohibited. Idle up (control of combustion worsening).	Pass condition detected and then engine switch turned off
P001600 P001800	VVT system	The cam timing control motor with EDU assembly is operated to the most retarded position. Idle up (control of combustion worsening).	Pass condition detected and then engine switch turned off
P001700 P001900	VVT system	Exhaust VVT maximum advance contact. Idle up (control of combustion worsening).	Pass condition detected and then engine switch turned off
P006D62 P00F762	Vacuum sensor assembly Atmospheric pressure sensor (ECM)	Output power is limited.	Engine switch off
P00CF62 P00D062 P023511 P023515 P023911 P023915	No. 1 turbo pressure sensor	Boost prohibited.	Pass condition detected
P003012 P003013 P005012 P005013 P101A9E P103A9E	Air fuel ratio sensor (sensor 1) heater	The ECM turns off the air fuel ratio sensor (sensor 1) heater.	Engine switch off
P003312 P003314 P00C012 P00C014	Air by-pass valve assembly	Output power is limited.	Pass condition detected
P003612 P003613 P005612 P005613 P102A9E P105A9E	Air fuel ratio sensor (sensor 2) heater	The ECM turns off the air fuel ratio sensor (sensor 2) heater.	Engine switch off
P007A11 P007A15	Intake air temperature sensor (No. 3 turbo pressure sensor)	The ECM estimates the intake air temperature to be 45°C (113°F). Output power is limited.	Pass condition detected
P008700 P008800 P123513 P123613	Fuel pump assembly (for high pressure side)	Output power is limited. Fuel pressure is set to 200 kPa (2 kgf/cm², 29 psi)	Engine switch off
P00AA11 P00AA15 P011011 P011015	Intake air temperature sensor (mass air flow meter sub-assembly)	Boost prohibited. The ECM estimates the intake air temperature to be 20°C (68°F).	Pass condition detected and then engine switch turned off
P010012 P010014 P010A12 P010A14	Mass air flow meter sub-assembly	Boost prohibited.	Pass condition detected and then engine switch turned off
P011511 P011515	Engine coolant temperature sensor (for outlet side)	The ECM estimates the outlet side engine coolant temperature to be 80°C (176°F). The target engine coolant temperature is set to 82°C.	Pass condition detected
P01E311 P01E315	Engine coolant temperature sensor (for inlet side)	The engine coolant temperature judgment value (for inlet side) is changed to the outlet coolant temperature - 5°C. The target engine coolant temperature is set to 82°C.	Pass condition detected
P012011 P012015 P01201C P022011 P022015 P022511 P022515 P02251C P060444 P060647 P060747 P060787 P060D49 P060E49 P061347 P065714 P06579E P160700 P16B09F P210018 P210019 P210A18 P210A19 P211172 P211173 P211900 P211904 P211977 P21199B P211D00 P211D77 P212A11 P212A15 P21352B P266914 P26699E P2AD12B	Electronic throttle control system	Boost prohibited. The ECM cuts off throttle actuator current for both bank 1 and bank 2, and the throttle valve is returned to a 8° throttle position by the return spring. The ECM then adjusts the engine output by controlling fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal angle to allow the vehicle to be driven at a low speed*1.	Pass condition detected and then engine switch turned off
P019011 P019015	Fuel pressure sensor (for high pressure)	Output power is limited. Fuel pressure is set to 200 kPa (2 kgf/cm², 29 psi)	Engine switch off
P020113 P020213 P020313 P020413 P020513 P020613 P062D13	ECM (injector driver)	Fuel cut is performed and then the output is limited when the engine speed is 1000 rpm or more.	Pass condition detected and then engine switch turned off
P023400 P02351C P02391C P02CA00	Turbocharger system	Boost prohibited.	Engine switch off
P024300 P024318 P024319 P024700 P024718 P024719 P25B372 P25B473 P25B572 P25B673 P2AB711 P2AB715 P2ABA11 P2ABA15	Waste gate valve actuator assembly	Boost prohibited.	Pass condition detected and then engine switch turned off
P026A00	Intercooler system	Output power is limited.	Pass condition detected
P030000 P030027 P030085 P030100 P030200 P030300 P030400 P030500 P030600 *2	Port fuel injector assembly Direct fuel injector assembly Electronic throttle control system	When a catalyst-damaging misfire occurs (MIL blinking), the following fail-safe operation is performed for catalyst overheat malfunction prevention. Under a low load and at a low engine speed: - Fuel cut is performed on the malfunctioning cylinder. Under a high load and at a high engine speed: - Throttle valve opening angle control is performed. - Fuel cut is performed on all cylinders or the malfunctioning cylinder.	Pass condition detected and then engine switch turned off
P032511 P032515 P033011 P033015	Knock control sensor	The ECM sets the ignition timing to maximum retard.	Engine switch off
P05042B	Stop light switch assembly	The accelerator pedal opening angle is fixed when there is an accelerator pedal malfunction or history of a malfunction.	Engine switch off
P056014	ECM +B circuit	Generator command is maintained.	Pass condition detected and then engine switch turned off
P107A11 P107A15	No. 2 fuel pressure sensor (for low pressure side)	Fuel pump (for low pressure side) control is maintained.	Engine switch off
P137800	Pre-ignition	Output is limited in low-speed boost region.	Clear DTC after recovering to normal condition
P15E517 P15E52A	Oil pressure sender gauge assembly	Control of oil pressure switching valve assembly is stopped.	Pass condition detected and then engine switch turned off
P16B318 P16B319 P16B871 P16B479	Water control valve	Control of water control valve is stopped. Output power is limited.	Pass condition detected and then engine switch turned off
P16B511 P16B515	Ball valve position sensor (water control valve)	Water control valve drive duty of 25% is output (only when the ambient temperature is 0°C (32°F) or higher). Output power is limited.	Pass condition detected and then engine switch turned off
P212012 P212014 P21201C P21201F P212099 P212512 P212514 P21251F P21382B	Accelerator pedal sensor assembly	The accelerator pedal position sensor has 2 sensor circuits: Main and Sub. If either circuit malfunctions, the ECM limits the engine output. If both circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.	Pass condition detected and then engine switch turned off
P218211 P218215	Engine coolant temperature sensor (for cylinder head side)	Water stop control of water control valve is prohibited.	Pass condition detected and then engine switch turned off
P21CF13 P21D013 P21D113 P21D213 P21D313 P21D413	Port fuel injector assembly	The ECM performs fuel-cut when the engine speed is 2000 rpm or more.	Pass condition detected and then engine switch turned off
P222611 P222615	Atmospheric pressure sensor (ECM)	Boost prohibited.	Engine switch off
P223711 P223712 P223713 P223716 P223717 P22371B P224011 P224012 P224013 P224016 P224017 P22401B P225111 P225112 P225411 P225412	Air fuel ratio sensor (sensor 1)	Air fuel ratio sensor (sensor 1) air fuel ratio feedback control is stopped.	Pass condition detected and then engine switch turned off
P22AB11 P22AB12 P22AB13 P22AB16 P22AB17 P22B211 P22B212 P22B811 P22B812 P22B813 P22B816 P22B817 P22BF11 P22BF12	Air fuel ratio sensor (sensor 2)	Control based on air fuel ratio sensor (sensor 2) air fuel ratio feedback is stopped. The ECM turns off the air fuel ratio sensor (sensor 2) heater.	Pass condition detected and then engine switch turned off
P23AA72 P2C2972	Air by-pass valve assembly	Output power is limited.	Pass condition detected and then engine switch turned off
P244B00 P246300 P246500	Gasoline particulate filter system	Output power is limited.	Engine switch off
P25AE00	Lubrication system	Control of oil pressure switching valve assembly is stopped. Output power is limited.	Pass condition detected

Tech Tips

*1: The vehicle can be driven slowly when the accelerator pedal is depressed firmly and slowly. If the accelerator pedal is depressed quickly, the vehicle may speed up and slow down erratically.
*2: Misfire-related fail-safe operations occur when catalyst overheat malfunctions occur.