REAR BUMPER(for Wagon) REASSEMBLY

PROCEDURE

1. INSTALL REAR BUMPER ARM SUB-ASSEMBLY LH

   1. 

      Install the rear bumper arm sub-assembly LH with the 3 bolts.

      11.5 N*m

      117 kgf*cm

      8 ft.*lbf

2. INSTALL REAR BUMPER ARM SUB-ASSEMBLY RH

   Tip:

   Use the same procedure as for the LH side.

3. INSTALL NO. 1 REAR BUMPER REINFORCEMENT

   1. 

      Install the No. 1 rear bumper reinforcement with the 8 bolts.

      11.5 N*m

      117 kgf*cm

      8 ft.*lbf

4. INSTALL REAR BUMPER SIDE SEAL LH

   1. 

      Install the rear bumper side seal LH with the 3 clips.

5. INSTALL REAR BUMPER SIDE SEAL RH

   1. 

      Install the rear bumper side seal RH with the 3 clips.

6. INSTALL UPPER REAR BUMPER RETAINER LH

   1. 

      Engage the 2 guides to temporarily install the upper rear bumper retainer LH to the rear combination light assembly LH.

   2. 

      Engage the 2 guides as shown in the illustration to temporarily install the upper rear bumper retainer LH and rear combination light assembly LH as a set.

   3. Install the upper rear bumper retainer LH with the screw.

7. INSTALL UPPER REAR BUMPER RETAINER RH

   Tip:

   Use the same procedure as for the LH side.

8. INSTALL REAR COMBINATION LIGHT ASSEMBLY LH

   Click here

9. INSTALL REAR COMBINATION LIGHT ASSEMBLY RH

   Tip:

   Use the same procedure as for the LH side.

10. INSTALL REAR BUMPER SIDE RETAINER LH

    1. 

       Engage the guide and 4 claws.

    2. 

       Install the rear bumper side retainer LH with the 3 screws.

11. INSTALL REAR BUMPER SIDE RETAINER RH

    Tip:

    Use the same procedure as for the LH side.

12. INSTALL NO. 2 REAR BUMPER MOULDING

    1. 

       Engage the 10 claws.

    2. Install the No. 2 rear bumper moulding to the rear bumper guard with the 2 screws.

    3. 

       Engage the guide and 10 claws.

    4. 

       Install the rear bumper guard with No. 2 rear bumper moulding with the 2 clips.

13. INSTALL REFLEX REFLECTOR ASSEMBLY LH

    1. 

       Engage the guide.

    2. Engage the claw.

    3. Install the reflex reflector assembly LH with the screw.

    4. 

       Engage the 6 claws to install the rear bumper extension LH.

14. INSTALL REFLEX REFLECTOR ASSEMBLY RH

    Tip:

    Use the same procedure as for the LH side.

15. INSTALL REAR BUMPER PAD LH

    1. Clean the rear bumper assembly.

       1. Remove any remaining double-sided tape from the rear bumper assembly.

       2. Wipe off any tape adhesive residue with cleaner.

    2. Remove the release paper from a new rear bumper pad LH.

       Tip:

       After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. 

       *a

       Line

       Install the rear bumper pad LH as shown in the illustration.

       Tip:

       Install the rear bumper pad LH along the line marked on the rear bumper assembly.

16. INSTALL REAR BUMPER PAD RH

    Tip:

    Use the same procedure as for the LH side.

17. INSTALL NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

    Click here

18. INSTALL NO. 3 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

    Click here

19. INSTALL NO. 3 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

    Click here

20. INSTALL NO. 2 LUGGAGE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)

    1. Engage the 4 clamps.

       

       *a	Line	-	-
       	Adhesive Tape	-	-

    2. Connect the 4 connectors.

    3. Install the No. 2 luggage room wire to the rear bumper assembly with adhesive tape as shown in the illustration.

       Note:

       • Apply the tape securely in place.

       • Do not touch the adhesive surface when applying the tape to prevent adhesion failure.