СИСТЕМА SFI Fuel Injector Circuit

DESCRIPTION

The fuel injector assembly are located on the intake manifold. They inject fuel into the cylinders based on signals from the ECM.

WIRING DIAGRAM

B006POWE01

CAUTION / NOTICE / HINT

Note

Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE


  1. CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)

    B006NOTC10
    *a

    Front view of wire harness connector

    (to Fuel Injector Assembly)

    1. Disconnect the fuel injector assembly connector.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      D24-1 - Body ground Engine switch on (IG) 11 to 14 V
      D10-1 - Body ground Engine switch on (IG) 11 to 14 V
      D23-1 - Body ground Engine switch on (IG) 11 to 14 V
      D9-1 - Body ground Engine switch on (IG) 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL INJECTOR ASSEMBLY) Click here

    OK

  2. INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)


    1. Inspect the fuel injector assembly.

      Click here

      Tech Tips

      Perform "Inspection After Repair" after replacing the fuel injector assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FUEL INJECTOR ASSEMBLY Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)


    1. Disconnect the fuel injector assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D24-2 - D1-21 (#10) Always Below 1 Ω
      D10-2 - D1-18 (#20) Always Below 1 Ω
      C23-2 - D1-19 (#30) Always Below 1 Ω
      C9-2 - D1-20 (#40) Always Below 1 Ω
      D24-2 or D1-21 (#10) - Body ground and other terminals Always 10 kΩ or higher
      D10-2 or D1-18 (#20) - Body ground and other terminals Always 10 kΩ or higher
      C23-2 or D1-19 (#30) - Body ground and other terminals Always 10 kΩ or higher
      C9-2 or D1-20 (#40) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  4. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL INJECTOR ASSEMBLY)


    1. Disconnect the fuel injector assembly connector.

    2. Disconnect the No. 1 integration relay connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1D-8 - D24-1 Always Below 1 Ω
      1D-8 - D10-1 Always Below 1 Ω
      1D-8 - D23-1 Always Below 1 Ω
      1D-8 - D9-1 Always Below 1 Ω
      1D-8 or D24-1 - Body ground and other terminals Always 10 kΩ or higher
      1D-8 or D10-1 - Body ground and other terminals Always 10 kΩ or higher
      1D-8 or D23-1 - Body ground and other terminals Always 10 kΩ or higher
      1D-8 or D9-1 - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    CHECK ECM POWER SOURCE CIRCUIT Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR