GENERATOR REASSEMBLY

PROCEDURE

  1. INSTALL GENERATOR DRIVE END FRAME BEARING

    1. A196742E01

      Using SST and a press, press in a new generator drive end frame bearing.

      09950-60010

      09951-00470

      09950-70010

      09951-07100

    2. A196740

      Install the retainer plate with the 4 screws.

      2.3 N*m

      23 kgf*cm

      20 in.*lbf

  2. INSTALL GENERATOR ROTOR ASSEMBLY

    1. A196745

      Place the generator drive end frame on the generator with clutch pulley.

    2. Install the generator rotor assembly to the generator drive end frame.

  3. INSTALL GENERATOR COIL ASSEMBLY

    1. A284548

      Install a new bearing cover packing.

      Note:

      Align the protrusion of the bearing cover packing with the groove of the generator coil assembly when installing.

    2. A213467C02

      *a

      21mm Deep Socket Wrench

      Using a 21 mm deep socket wrench and press, slowly press the generator coil assembly to install it.

    3. A292415

      Install the 4 bolts.

      5.9 N*m

      60 kgf*cm

      52 in.*lbf

  4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

    1. A196810C02

      *a

      Pin (1.0mm)

      While pushing the 2 brushes into the generator brush holder assembly, insert a 1.0 mm (0.0394 in.) pin into the generator brush holder assembly hole.

    2. A292414C02

      *a

      Pin (1.0mm)

      Install the generator brush holder assembly to the generator coil assembly with the 2 screws.

      1.8 N*m

      18 kgf*cm

      16 in.*lbf

    3. Pull out the pin from the generator brush holder assembly hole.

  5. INSTALL GENERATOR TERMINAL INSULATOR

    1. A285085

      Install the generator terminal insulator to the generator coil assembly.

      Note:

      Be sure to install the generator terminal insulator in the correct direction.

  6. INSTALL GENERATOR REAR END COVER

    1. A196748

      Install the generator rear end cover to the generator coil assembly with the 3 bolts.

      4.6 N*m

      47 kgf*cm

      41 in.*lbf

  7. INSTALL GENERATOR WITH CLUTCH PULLEY

    1. Temporarily install the generator with clutch pulley to the rotor shaft.

    2. Secure the generator drive end frame in a vise between aluminum plates.

    3. A292416C02

      *a

      Rotor Shaft

      Install SST (A) and (B) to the generator with clutch pulley as shown in the illustration.

      09820-63021

      Note:

      Securely attach SST to the generator with clutch pulley and generator rotor shaft.

    4. A292417C01

      *a

      Hold

      *b

      Turn

      *c

      Length of SST 100 mm (3.94 in.)

      *d

      Length of Torque Wrench 255 mm (10.0 in.)

      Tighten the pulley by turning SST (B) as shown in the illustration.

      without SST [Torque (N*m(kgf*cm, ft.*lbf))]

      111 N*m

      1132 kgf*cm

      82 ft.*lbf

      with SST [Reading of Torque wrench (N*m(kgf*cm, ft.*lbf))]

      84 N*m

      857 kgf*cm

      62 ft.*lbf

      Tip:

      • The "with SST" torque value is effective when SST is parallel to the torque wrench.

      • The "with SST" torque value is effective when using SST with a fulcrum length of 100 mm (3.94 in.).

      • The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 255 mm (10.0 in.).

      • If using a torque wrench with a different length, or connecting the torque wrench and SST at an angle, refer to the alternate torque values.

        Click hereClick here

    5. Remove SST from the generator with clutch pulley.

    6. Check that the generator with clutch pulley rotates smoothly.