КОРПУС ДРОССЕЛЬНОЙ ЗАСЛОНКИ СНЯТИЕ

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the throttle body with motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes) Stop and start system

Click here

Memorize steering angle neutral point Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Initialize servo motor Air conditioning system

Click here

Reset slide door close position Power slide door system

Click here

Reset back door close position Power back door system

Click here

Replacement of throttle body with motor assembly Inspection After Repair

  • Poor idle, etc.

  • Engine start function, etc.

Click here

Cleaning the deposits from the throttle body with motor assembly

PROCEDURE


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DRAIN ENGINE COOLANT

    Click here

  3. SEPARATE CENTER NO. 1 COWL TOP VENTILATOR LOUVER

    Click here

  4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  5. REMOVE BATTERY

    Click here

  6. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    1. B006N7P

      Disconnect the mass air flow meter sub-assembly connector and disengage the 2 wire harness clamps.

    2. B006KI1C01
      *a Air Cleaner Cap Clamp
      *b Guide

      Disengage the 2 air cleaner cap clamps.

    3. Open the air cleaner cap sub-assembly and remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.

    4. Disengage the 2 guides to separate the air cleaner cap sub-assembly from the air cleaner case sub-assembly.

    5. B006M2X

      Loosen the hose clamp and remove the air cleaner cap sub-assembly from the air cleaner hose assembly.

  7. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    1. B006OVE

      Disengage the clamp.

    2. Remove the 3 bolts and air cleaner case sub-assembly.

  8. REMOVE AIR CLEANER HOSE ASSEMBLY


    1. B006ODP

      Disengage the No. 2 fuel vapor feed hose from the air cleaner hose assembly.

    2. Disengage the purge valve (purge VSV) from the air cleaner hose assembly.

    3. B006M3K

      Slide the clip and disconnect the ventilation hose from the cylinder head cover sub-assembly.

    4. B006P2B

      Loosen the hose clamp and remove the air cleaner hose assembly from the throttle body with motor assembly.

  9. REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY


    1. B006OCKC01
      *1 Fuel Tube Sub-assembly
      *2 Breather Plug Hose

      Disconnect the throttle body with motor assembly connector.

    2. Disengage the fuel tube sub-assembly and breather plug hose from the fuel hose bracket.

    3. B006OVO

      Remove the bolt and fuel hose bracket from the throttle body with motor assembly.

    4. B006RF5

      Remove the 4 bolts and throttle body with motor assembly from the intake manifold.

      Note

      If the throttle body with motor assembly has been struck or dropped, replace it.

    5. B006MTFC01
      *1 No. 1 Water By-pass Hose
      *2 No. 2 Water By-pass Hose

      Slide the 2 clips and disconnect the No. 1 water by-pass hose and No. 2 water by-pass hose from the throttle body with motor assembly.

  10. REMOVE THROTTLE BODY GASKET


    1. B006O5H

      Remove the throttle body gasket from the intake manifold.