AUTOMATIC TRANSAXLE FLUID REPLACEMENT

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during automatic transaxle fluid replaced are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

  • Replacement of automatic transaxle assembly*1

  • Replacement of automatic transaxle fluid*1

 Bleed the oil pump assembly with motor (automatic transaxle assembly) Stop and start system

Click here


PROCEDURE


  1. PREPARATION WORK

    Click here

  2. REPLACE AUTOMATIC TRANSAXLE FLUID


    1. Lift the vehicle. [#1]

      Note

      Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure the tilt angle from the front to rear of the vehicle is within +/- 1°).

    2. B007ZF6

      Remove the refill plug and gasket from the rear transaxle cover sub-assembly. [#2]

    3. B007WWT

      Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle oil pan sub-assembly. [#3]

    4. B007Z9KC02
      *1 No. 1 Transmission Oil Filler Tube
      *a 6 mm Hexagon Socket Wrench

      Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle oil pan sub-assembly and drain the automatic transaxle fluid. [#4]

    5. A01VV53

      Measure the amount of automatic transaxle fluid drained. [#5]

      Tech Tips

      Add the same amount of automatic transaxle fluid in step [#8].

    6. Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the automatic transaxle oil pan sub-assembly. [#6]

      Torque:
      1.7 N*m  { 17 kgf*cm, 15 in.*lbf }
    7. B007WWT

      Using a 6 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the automatic transaxle oil pan sub-assembly. [#7]

      Tech Tips

      Reuse the old gasket as the overflow plug will be removed again to adjust the automatic transaxle fluid level.

    8. B007X32

      Add automatic transaxle fluid to the refill hole using the same amount of automatic transaxle fluid drained in step [#5]. [#8]

      Note

      Use Toyota Genuine ATF WS.

    9. B007ZF6

      Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage. [#9]

      Tech Tips

      Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.

    10. Lower the vehicle. [#10]

    11. Start the engine. [#11]

    12. Slowly move the shift lever from P to D, and then back to P. [#12]

      Tech Tips

      Slowly move the shift lever to circulate the automatic transaxle fluid through each part of the automatic transaxle assembly.

    13. Allow the engine to idle for 30 seconds to warm it up. [#13]

    14. Turn the engine switch off. [#14]

    15. Repeat steps [#1] to [#14].

    16. Repeat steps [#1] to [#10].

  3. ADD SPECIFIED AMOUNT OF AUTOMATIC TRANSAXLE FLUID

    Click here

  4. BLEED AIR FROM OIL PUMP WITH MOTOR ASSEMBLY

    Click here

  5. ADJUST AUTOMATIC TRANSAXLE FLUID TEMPERATURE (when Using the GTS)

    Click here

  6. ADJUST AUTOMATIC TRANSAXLE FLUID TEMPERATURE (when Not Using the GTS)

    Click here

  7. ADJUST AUTOMATIC TRANSAXLE FLUID LEVEL

    Click here

  8. REBUILD WORK

    Click here