КОРПУС ДРОССЕЛЬНОЙ ЗАСЛОНКИ СНЯТИЕ

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the throttle body with motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure	Necessary Procedures	Effects/Inoperative when not Performed	Link
Battery terminal is disconnected/reconnected	Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)	Stop and start system	Click here
	Memorize steering angle neutral point	Panoramic view monitor system	Click here
	Initialize back door lock	Power door lock control system	Click here
	Initialize servo motor	Air conditioning system	Click here
	Reset slide door close position	Power slide door system	Click here
	Reset back door close position	Power back door system	Click here
Replacement of throttle body with motor assembly	Inspection After Repair	Poor idle, etc. Engine start function, etc.	Click here
Cleaning the deposits from the throttle body with motor assembly	Inspection After Repair	Poor idle, etc. Engine start function, etc.	Click here
Replacement of battery	Switch battery type	Stop and Start System	Click here

PROCEDURE

PRECAUTION

Note

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here
DRAIN ENGINE COOLANT

Click here
SEPARATE CENTER NO. 1 COWL TOP VENTILATOR LOUVER

Click here
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here
REMOVE BATTERY

Click here
REMOVE AIR CLEANER CAP SUB-ASSEMBLY
1. Disconnect the mass air flow meter sub-assembly connector and disengage the 2 wire harness clamps.
2. *a Air Cleaner Cap Clamp
  
  *b Guide
  
  Disengage the 2 air cleaner cap clamps.
3. Open the air cleaner cap sub-assembly and remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.
4. Disengage the 2 guides to separate the air cleaner cap sub-assembly from the air cleaner case sub-assembly.
5. Loosen the hose clamp and remove the air cleaner cap sub-assembly from the air cleaner hose assembly.
REMOVE AIR CLEANER CASE SUB-ASSEMBLY
1. Disengage the clamp.
2. Remove the 3 bolts and air cleaner case sub-assembly.
REMOVE AIR CLEANER HOSE ASSEMBLY
1. Disengage the No. 2 fuel vapor feed hose from the air cleaner hose assembly.
2. Disengage the purge valve (purge VSV) from the air cleaner hose assembly.
3. Slide the clip and disconnect the ventilation hose from the cylinder head cover sub-assembly.
4. Loosen the hose clamp and remove the air cleaner hose assembly from the throttle body with motor assembly.
REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY
1. *1 Fuel Tube Sub-assembly
  
  *2 Breather Plug Hose
  
  Disconnect the throttle body with motor assembly connector.
2. Disengage the fuel tube sub-assembly and breather plug hose from the fuel hose bracket.
3. Remove the bolt and fuel hose bracket from the throttle body with motor assembly.
4. Remove the 4 bolts and throttle body with motor assembly from the intake manifold.
  
  Note
  
  If the throttle body with motor assembly has been struck or dropped, replace it.
5. *1 No. 1 Water By-pass Hose
  
  *2 No. 2 Water By-pass Hose
  
  Slide the 2 clips and disconnect the No. 1 water by-pass hose and No. 2 water by-pass hose from the throttle body with motor assembly.
REMOVE THROTTLE BODY GASKET
1. Remove the throttle body gasket from the intake manifold.

*a	Air Cleaner Cap Clamp
*b	Guide

*1	Fuel Tube Sub-assembly
*2	Breather Plug Hose

*1	No. 1 Water By-pass Hose
*2	No. 2 Water By-pass Hose