OIL AND OIL FILTER REPLACEMENT

CAUTION / NOTICE / HINT

CAUTION:


  • Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner to remove any used engine oil thoroughly. Do not use gasoline, thinners or solvents.

  • In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.

PROCEDURE


  1. REMOVE ENGINE SERVICE HOLE COVER


    1. A004MTJ

      Remove the 3 screws and engine service hole cover from the No. 1 engine under cover.

  2. DRAIN ENGINE OIL


    1. Remove the oil filler cap sub-assembly.

    2. A004OA0

      Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

    3. Install a new gasket and the oil pan drain plug.

      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

  3. REMOVE NO. 1 ENGINE COVER

    Click here

  4. REMOVE RADIATOR SUPPORT OPENING COVER

    Click here

  5. REMOVE OIL FILTER SUB-ASSEMBLY


    1. A004O77

      Using a 27 mm socket wrench, remove the oil filter cover.

    2. A004RP3E02
      Text in Illustration
      *1 Oil Filter Sub-assembly
      *2 Oil Filter Cover
      *3 O-Ring

      Remove the 2 O-rings from the oil filter sub-assembly and the oil filter cover.

      Note

      Be sure to remove the O-ring by hand without using any tools to prevent damage to the O-ring groove.

    3. Remove the oil filter sub-assembly from the oil filter cover.

  6. INSTALL OIL FILTER SUB-ASSEMBLY


    1. Clean the inside of the oil filter cover, its threads and its O-ring.

    2. A004T48E03
      Text in Illustration
      *1 O-Ring
      *a CORRECT
      *b INCORRECT

      Apply a small amount of engine oil to a new O-ring and install it to the oil filter cover.

      Note


      • Be sure to install the O-ring in the proper location, otherwise oil may leak.

      • Do not twist the O-ring.

    3. Apply a light coat of engine oil to a new O-ring.

    4. A004U6SE03
      Text in Illustration
      *1 O-Ring
      *a Oil Filter Assembly Hole
      A004NPW Protrusion

      Install the O-ring to the oil filter sub-assembly.

    5. Set a new oil filter sub-assembly in the oil filter assembly.

      Note

      Insert the protrusion of the oil filter sub-assembly into the oil filter assembly hole.

    6. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cover.

    7. A004P1UE03
      Text in Illustration
      *1 Oil Filter Assembly
      *2 O-Ring
      *3 Oil Filter Cover
      *a No Gap

      Using a 27 mm socket wrench, tighten the oil filter cover.

      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

      Note

      After tightening the oil filter cover, make sure that there is no gap and that the O-ring is not protruding.

  7. ADD ENGINE OIL


    1. Add new engine oil.

      Standard engine oil
      Toyota recommends the use of approved "Toyota Genuine Motor Oil 5W-30 Premium Fuel Economy for 1WW/2WW engines" or equivalent.
      Standard capacity (Drain and refill with oil filter change)
      5.2 liters (5.5 US qts, 4.6 Imp. qts)

      Tech Tips

      Refer to "OIL SPEC LIST" for the standard engine oil.

  8. INSPECT FOR OIL LEAK


    1. Start the engine. Make sure that there are no oil leaks from the areas that were worked on.

  9. INSPECT ENGINE OIL LEVEL

    Click here

  10. INSTALL RADIATOR SUPPORT OPENING COVER

    Click here

  11. INSTALL NO. 1 ENGINE COVER

    Click here

  12. INSTALL ENGINE SERVICE HOLE COVER


    1. Install the engine service hole cover with the 3 screws to the No. 1 engine under cover.

  13. OIL SPEC LIST


    1. Equivalent engine oils of matching quality which can be used are referred to in the list of approved engine oils.

      A004TE4
      A004PRW
      A004SEE
      A004RF0
      A004MX8
      A004SXT
      A004T2Z