ECD SYSTEM, Diagnostic DTC:P0335 and P0336

DTC Code DTC Name
P0335 Crankshaft Position Sensor "A" Circuit
P0336 Crankshaft Position Sensor "A" Circuit Range / Performance

DESCRIPTION

The crankshaft position sensor is installed to the gearbox case.

The crankshaft position sensor records the position of the crankshaft with the aid of a sensor wheel screwed to the flywheel.

The ECM uses the signals to calculate the duration as well as the length of one crankshaft revolution.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

P0335

Crankshaft Position Sensor "A" Circuit

No crankshaft position sensor signal to ECM while cranking.

(3 trip detection logic)

  • Open or short in crankshaft position sensor circuit

  • Crankshaft position sensor

  • ECM

Does not come on

DTC stored

P0336

Crankshaft Position Sensor "A" Circuit Range / Performance

Wrong pattern of signal from sensor is detected.

(3 trip detection logic)

  • Open or short in crankshaft position sensor circuit

  • Crankshaft position sensor

  • ECM

Does not come on

DTC stored

WIRING DIAGRAM

A351169E05

CAUTION / NOTICE / HINT

Note:

When replacing the ECM, the ECM needs registration and initialization.

Click here

Tip:

  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Check the value on the GTS.

    1. Connect the GTS to the DLC3.

    2. Start the engine and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

  • The engine speed can be confirmed in the Data List using the GTS. If there are no NE signals from the crankshaft position sensor despite the engine running, the engine speed will be indicated as zero. If the voltage output of the crankshaft position sensor is insufficient, the engine speed will be indicated as lower than the actual engine speed.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE

  1. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

    1. Disconnect the crankshaft position sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      B114-2 (NE) - B112-121 (NE+)

      Always

      Below 1 Ω

      B114-3 (NE-) - B112-90 (NE-)

      Always

      Below 1 Ω

      B114-1 (VG) - B112-122 (VCNE)

      Always

      Below 1 Ω

      B114-2 (NE) or B112-121 (NE+) - Body ground

      Always

      10 kΩ or higher

      B114-3 (NE-) or B112-90 (NE-) - Body ground

      Always

      10 kΩ or higher

      B114-1 (VG) or B112-122 (VCNE) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTORClick here

    OK

  2. CHECK HARNESS AND CONNECTOR (POWER SOURCE)

    A351158C21

    *a

    Front view of wire harness connector

    (to Crankshaft Position Sensor)

    1. Disconnect the crankshaft position sensor connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Switch Condition

      Specified Condition

      B114-1 (VG) - Body ground

      Ignition switch ON

      4.5 to 5.5 V

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE ECMClick here

    OK

  3. CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

    1. Check the crankshaft position sensor installation.

      OK

      Sensor is installed correctly.

    Result

    Proceed to

    OK

    NG
    NG

    SECURELY REINSTALL SENSORClick here

    OK

  4. REPLACE CRANKSHAFT POSITION SENSOR

    1. Replace crankshaft position sensor.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

  5. CHECK WHETHER DTC OUTPUT RECURS (DTC P0335 AND/OR P0336)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

      Powertrain > Engine and ECT > Trouble Codes

    8. Read the DTCs.

      Result

      Result

      Proceed to

      No DTC output

      A

      DTC P0335 and/or P0336

      B
    A

    END

    B

    REPLACE ECMClick here

  6. SECURELY REINSTALL SENSOR

    1. Securely reinstall crankshaft position sensor.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  7. REPLACE ECM

    1. Replace the ECM.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  8. REPAIR OR REPLACE HARNESS OR CONNECTOR

    1. Repair or replace the harness or connector.

    Result

    Proceed to

    NEXT
    NEXT

  9. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

      Powertrain > Engine and ECT > Trouble Codes

    8. Confirm that the DTC is not output again.

    Result

    Proceed to

    NEXT
    NEXT

    END