Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Tech Tips
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
DATA LIST
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / DRS / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Rear Wheel Angle(Motor Resolver) | Rear wheel angle (motor resolver) | Min.: -8.00 deg Max.: 7.99 deg |
-1.0 to 1.0 deg | - |
| Rear Wheel Angle Changing Speed | Rear wheel angle changing speed | Min.: -8.00 deg/s Max.: 7.99 deg/s |
-8.00 to 7.99 deg/s | - |
| Vehicle Speed | Rear wheel angle changing speed | Min.: 0.00 km/h (0 mph) Max.: 327.67 km/h (203 mph) |
Actual vehicle speed | - |
| Starting Status | Starting status | Stop or Starting-up | Engine stopped: Stop Engine running: Starting-up |
- |
| IG Power Supply Voltage | IG power supply voltage | Min.: 0.00 V Max.: 255.99 V |
10.5 to 16 V | - |
| PIG Power Supply Voltage | PIG power supply voltage | Min.: 0.00 V Max.: 255.99 V |
11 to 14 V | - |
| Power Supply Status | Power supply status | Unreceived, Prompt Stop, Cur Pos Stop, N Pos Stop or Normal | Normal | If the result is not as specified, the vehicle power supply voltage may be low |
| Limited Current | Limited current | Min.: -256.00 A Max.: 255.99 A |
-60 to 60 A | - |
| Voltage before Pressure Rising | Voltage before pressure rising | Min.: 0.00 V Max.: 255.99 V |
11 to 14 V | - |
| Voltage after Pressure Rising | Voltage after pressure rising | Min.: 0.00 V Max.: 255.99 V |
11 to 14 V | - |
| System Heavily-loaded Status | System heavily-loaded status | OFF or ON | OFF | - |
| ECU Substrate Temperature | ECU substrate temperature | Min.: -256.00°C (-428°F) Max.: 255.99°C (492°F) |
-40 to 120°C (-40 to 248°F) | - |
| Motor Temperature(ECU Calculated Value) | Motor temperature (ECU calculated value) | Min.: -256.00°C (-428°F) Max.: 255.99°C (492°F) |
70 to 140°C (158 to 284°F) | - |
| ECU Substrate Temperature(ECU Calculated Value) | ECU substrate temperature (ECU calculated value) | Min.: -256.00°C (-428°F) Max.: 255.99°C (492°F) |
-40 to 120°C (-40 to 248°F) | - |
| Ambient Temperature | Ambient temperature | Min.: -40°C (-40°F) Max.: 50°C (122°F) |
Same as ambient temperature | - |
| System Overheat Status | System overheat status | Normal, Overheat-Weak or Overheat-Strong | Normal | If the result is not as specified, the applied load to the DRS system may be high |
| Motor Resolver Electrical Angle | Motor resolver electrical angle | Min.: 0.00 deg Max.: 359.99 deg |
0.00 to 359.99 deg | - |
| Changing Amount of Motor Resolver Electrical Angle | Changing amount of motor resolver electrical angle | Min.: -180.00 deg Max.: 179.99 deg |
-30 to 30 deg | - |
| Motor Resolver SIN Phase Shaped Width | Motor resolver SIN phase amplitude | Min.: -5.00 V Max.: 4.99 V |
-3.5 to 3.5 V | - |
| Motor Resolver SIN Phase Offset | Motor resolver SIN phase offset | Min.: 0.00 V Max.: 19.99 V |
8 to 12 V | - |
| Motor Resolver COS Phase Shaped Width | Motor resolver COS phase amplitude | Min.: -5.00 V Max.: 4.99 V |
-3.5 to 3.5 V | - |
| Motor Resolver COS Phase Offset | Motor resolver COS phase offset | Min.: 0.00 V Max.: 19.99 V |
8 to 12 V | - |
| Motor Resolver Shaped Width Squared Sum | Sum of squares of motor resolver amplitudes | Min.: 0.00 V^2 Max.: 25.00 V^2 |
5.7 to 12.3 V^2 | - |
| Stroke Resolver Electrical Angle | Stroke resolver electrical angle | Min.: 0.00 deg Max.: 359.99 deg |
25 to 325 deg | - |
| Standard Value of Stroke Resolver Electrical Angle | Standard value of stroke resolver electrical angle | Min.: 0.00 deg Max.: 359.99 deg |
170 to 190 deg | - |
| Stroke Resolver SIN Phase Shaped Width | Stroke resolver SIN phase amplitude | Min.: -5.00 V Max.: 4.99 V |
-3.5 to 3.5 V | - |
| Stroke Resolver SIN Phase Offset | Stroke resolver SIN phase offset | Min.: 0.00 V Max.: 19.99 V |
8 to 12 V | - |
| Stroke Resolver COS Phase Shaped Width | Stroke resolver COS phase amplitude | Min.: -5.00 V Max.: 4.99 V |
-3.5 to 3.5 V | - |
| Stroke Resolver COS Phase Offset | Stroke resolver COS phase offset | Min.: 0.00 V Max.: 19.99 V |
8 to 12 V | - |
| Stroke Resolver Shaped Width Squared Sum | Sum of squares of stroke resolver amplitudes | Min.: 0.00 V^2 Max.: 25.00 V^2 |
5.7 to 12.3 V^2 | - |
| Motor Resolver Neutral Compensation Value | Motor resolver neutral compensation value | Min.: 0.00 deg Max.: 359.99 deg |
0 to 359.99 deg | - |
| Rear Wheel Angle Taking Status on Start-up | Rear wheel angle taking status on start-up | Unknown, Motor Resolver or Stroke Resolver | Motor Resolver | If the result is not as specified, the DRS system may be malfunctioning |
| Rear Wheel Target Angle(L-CAN) | Rear wheel target angle (L-CAN) | Min.: -8.00 deg Max.: 7.99 deg |
-1.0 to 1.0 deg | - |
| Rear Wheel Target Angle(G-CAN) | Rear wheel target angle (G-CAN) | Min.: -8.00 deg Max.: 7.99 deg |
-1.0 to 1.0 deg | - |
| Rear Wheel Angle(Stroke Sensor) | Rear wheel angle (stroke sensor) | Min.: -8.00 deg Max.: 7.99 deg |
-1.0 to 1.0 deg | - |
| Motor U Phase Voltage | Motor U phase voltage | Min.: 0.00 V Max.: 255.99 V |
0 to 34 V | - |
| Motor V Phase Voltage | Motor V phase voltage | Min.: 0.00 V Max.: 255.99 V |
0 to 34 V | - |
| Motor W Phase Voltage | Motor W phase voltage | Min.: 0.00 V Max.: 255.99 V |
0 to 34 V | - |
| Motor U Phase Current | Motor U phase current | Min.: -256.00 A Max.: 255.99 A |
-57 to 57 A | - |
| Motor V Phase Current | Motor V phase current | Min.: -256.00 A Max.: 255.99 A |
-57 to 57 A | - |
| Motor W Phase Current | Motor W phase current | Min.: -256.00 A Max.: 255.99 A |
-57 to 57 A | - |
| Motor U Phase Duty | Motor U phase duty | Min.: 0.00 % Max.: 100.00 % |
9 to 91 % | - |
| Motor V Phase Duty | Motor V phase duty | Min.: 0.00 % Max.: 100.00 % |
9 to 91 % | - |
| Motor W Phase Duty | Motor W phase duty | Min.: 0.00 % Max.: 100.00 % |
9 to 91 % | - |
| Motor Rotation Speed | Motor rotation speed | Min.: -32768 deg/s Max.: 32767 deg/s |
-32768 to 32767 deg/s | - |
| Actuator Operation Amount | Actuator operation amount | Too Little, Normal, Malfunction or Too Much | Normal | - |
| Limited Control Count(Overheat-Weak) | Limited control count (overheat-weak) | Min.: 0 Max.: 225 |
0 | - |
| Limited Control Count(Overheat-Strong) | Limited control count (overheat-strong) | Min.: 0 Max.: 225 |
0 | - |
| N Pos Stop Control Count | N pos stop control count | Min.: 0 Max.: 225 |
0 | - |
| Cur Pos Stop Control Count | Cur pos stop control count | Min.: 0 Max.: 225 |
0 | - |
| Prompt Stop Control Count | Prompt stop control count | Min.: 0 Max.: 225 |
0 | - |
| Power Supply Voltage Lowering Control Count | Power supply voltage lowering control count | Min.: 0 Max.: 225 |
0 | - |
| Limited Control Count(System Heavily-loaded) | Limited control count (system heavily-loaded) | Min.: 0 Max.: 225 |
0 | - |
| VGRS System Status | VGRS system status | Normal or Malfunction | Normal | - |
| Number of DTC | Number of DTC | Min.: 0 Max.: 225 |
0 | - |