AUDIO AND VISUAL SYSTEM(w/o Multi-display) Radio Broadcast cannot be Received (Bad Reception)

DTC Code DTC Name
Radio Broadcast cannot be Received (Bad Reception)

PROCEDURE

  1. CHECK RADIO RECEIVER ASSEMBLY

    1. Check the radio automatic station search function.

      1. Check the radio automatic station search function by activating it.

        OK

        The radio automatic station search function works properly.

        Result

        Result

        OK

        NG
    OK

    REPLACE RADIO RECEIVER ASSEMBLY

    Click here

    NG

  2. CHECK OPTIONAL COMPONENTS

    1. Check for optional components (sunshade film, telephone antenna, etc.).

      1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

        OK

        Optional components are installed.

        Note:

        Do not remove any optional components installed by the customer without his or her consent.

        Result

        Result

        OK

        NG
    OK

    REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

    NG

  3. CHECK RADIO RECEIVER ASSEMBLY

    1. E187251

      Remove the antenna connector from the radio receiver assembly.

    2. Turn the engine switch on (ACC) with the radio receiver assembly connector connected.

    3. Turn the radio on and tune into AM mode.

    4. Place a screwdriver, thin wire or other metal object on the radio receiver antenna jack and check that noise can be heard from the speaker.

      OK

      Noise occurs.

      Result

      Result

      OK

      NG
    NG

    REPLACE RADIO RECEIVER ASSEMBLY

    Click here

    OK

  4. CHECK GLASS ANTENNA

    1. E111994C04

      *a

      Tester Probe

      *b

      Antenna Wire

      *c

      Tin Foil

      Check for continuity of the antenna.

      Tip:

      Check for continuity at the center of each antenna wire as shown in the illustration.

      Note:

      When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of the probe and press the foil against the wire with your finger, as shown in the illustration.

      OK

      There is continuity in the antenna.

      Result

      Result

      OK

      NG
    NG

    REPAIR GLASS ANTENNA

    OK

  5. CHECK RADIO RECEIVER ASSEMBLY

    1. E188455C03

      *a

      Component without harness connected

      (Radio Receiver Assembly)

      Disconnect the RA radio receiver assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Switch Condition

      Specified Condition

      RA-5 (ANT+) - Body ground

      Engine switch on (IG), radio switch on

      11 to 14 V

      Result

      Result

      OK

      NG
    NG

    REPLACE RADIO RECEIVER ASSEMBLY

    Click here

    OK

  6. CHECK ANTENNA CORD SUB-ASSEMBLY

    1. Remove the antenna connector of the radio receiver and antenna.

    2. Measure the resistance between the antenna and radio receiver to check for an open circuit in the antenna cord.

      Standard resistance

      Below 1 Ω

    3. Measure the resistance between the antenna cord and body ground to check for a short circuit in the antenna cord.

      Standard resistance

      10 kΩ or higher

      Result

      Result

      OK

      NG
    NG

    REPLACE ANTENNA CORD SUB-ASSEMBLY

    OK

  7. REPLACE HOLDER ANTENNA ASSEMBLY

    1. Replace the holder antenna assembly and check if radio broadcasts can be received normally.

      Click here

      OK

      Radio broadcasts can be received.

      Result

      Result

      OK

      NG
    OK

    NORMAL OPERATION

    NG

    REPLACE RADIO RECEIVER ASSEMBLY

    Click here