HOOD LOCK CONTROL CABLE ASSEMBLY INSTALLATION

CAUTION / NOTICE / HINT

Tip:

  • Use the same procedure for LHD and RHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • A bolt without a torque specification is shown in the standard bolt chart (Click here).

PROCEDURE

  1. INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY (for LHD)

    1. B184768E04

      Tie the string that was passed through the engine compartment to the end of the hood lock control cable assembly as shown in the illustration.

      Table 1. Text in Illustration

      *1

      String

    2. Pull the string until the hood lock control cable grommet contacts the dash panel, and then connect the clamps shown in the illustration to install the cable.

      B341942E02
      Table 2. Text in Illustration

      *1

      Hood Lock Control Cable Assembly

      *2

      Clamp

      *3

      Radiator Support Side

      *4

      Headlight

      *5

      Wire Harness

      *6

      Wire Harness Clamp

      *7

      Dash Panel

      *8

      Grommet

      *9

      Hood Lock Control Cable Clamp

      -

      -

  2. INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY (for RHD)

    1. B184768E04

      Tie the string that was passed through the engine compartment to the end of the hood lock control cable assembly as shown in the illustration.

      Table 3. Text in Illustration

      *1

      String

    2. Pull the string until the hood lock control cable grommet contacts the dash panel, and then connect the clamps shown in the illustration to install the cable.

      B341943E02
      Table 4. Text in Illustration

      *1

      Hood Lock Control Cable Assembly

      *2

      Clamp

      *3

      Radiator Support Side

      *4

      Headlight

      *5

      Wire Harness

      *6

      Wire Harness Clamp

      *7

      Dash Panel

      *8

      Grommet

      *9

      Hood Lock Control Cable Clamp

      10

      Radiator Hose

      *11

      Washer Hose

      *12

      Washer Hose Clamp

  3. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

    1. B213797

      Connect the hood lock control cable assembly.

    2. Attach the 3 claws to install the hood lock control lever sub-assembly.

      Note:

      Make sure the cable inside the cabin does not interfere with the clutch pedal, link or accelerator pedal.

  4. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

    Click here

  5. INSTALL HOOD LOCK ASSEMBLY

    1. B229445E03

      Apply MP grease to the sliding areas of the lock.

      Table 5. Text in Illustration

      *1

      MP grease

    2. for LHD:

      1. B229446

        Connect the hood lock control cable.

      2. B229444

        Install the hood lock with the 3 bolts.

        7.5 N*m

        76 kgf*cm

        66 in.*lbf

    3. for RHD:

      1. B222493

        Connect the hood lock control cable.

      2. B222492

        Connect the connector.

      3. Install the hood lock with the 3 bolts.

        7.5 N*m

        76 kgf*cm

        66 in.*lbf

  6. INSTALL NO. 1 WATER HOSE CLAMP BRACKET

    Click here

  7. INSTALL FRONT FENDER LINER LH

    1. Install the front fender liner (Click here).

  8. INSTALL RADIATOR SUPPORT OPENING COVER

    Click here

  9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).