ECD SYSTEM, Diagnostic DTC:U010E

DTC Code DTC Name
U010E Lost Communication with Reductant Control Module

DESCRIPTION

The ECM sends and receives data to and from the urea pump control ECU via local CAN communication.

U010E
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
1.6 seconds or more after turning the ignition switch to ON. Communication stops between the ECM and the urea pump control ECU for 1.6 seconds or more.

  • Urea pump control ECU

  • Harness or connector

  • ECM

MONITOR DESCRIPTION

The ECM stores a DTC when a communication malfunction occurs between the ECM and urea pump control ECU.

WIRING DIAGRAM

B007OIJE01

INSPECTION PROCEDURE

Note

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

Tech Tips

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK DTC OUTPUT


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. According to the display on the GTS, select "Health Check".

    4. Check for currently output system DTCs.

      Result
      Result Proceed to
      DTC U010E is output A
      DTC U010E and other DTCs are output* B

      Tech Tips

      *: If any other DTCs are output, perform troubleshooting for those DTCs first.


    B

    GO TO DTC CHART Click here

    A

  2. CHECK HARNESS AND CONNECTOR (UREA PUMP CONTROL ECU - ECM)


    1. Disconnect the urea pump control ECU connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A45-27 (CAN+) - B97-41 (CANU) Always Below 1 Ω
      A45-26 (CAN-) - B97-56 (CAND) Always Below 1 Ω
      A45-27 (CAN+) or B97-41 (CANU) - Body ground and other terminals Always 10 kΩ or higher
      A45-26 (CAN-) or B97-56 (CAND) - Body ground and other terminals Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS AND CONNECTOR

    OK

  3. CHECK UREA PUMP CONTROL ECU (BATT TERMINAL)


    1. B007T47E32
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Urea Pump Control ECU)

      Disconnect the urea pump control ECU connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      A45-30 (BATT) - Body ground Always 11 to 14 V

    NG

    REPLACE UREA PUMP CONTROL ECU Click here

    OK

  4. CHECK DCU RELAY


    1. Inspect the DCU relay Click here.


    NG

    REPLACE DCU MAIN RELAY (DCU)

    OK

  5. CHECK UREA PUMP CONTROL ECU (UREL TERMINAL)


    1. Remove the DCU relay from the instrument panel relay block.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      DCU relay terminal 1 - Body ground Ignition switch ON 11 to 14 V

    NG

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL RELAY BLOCK - UREA PUMP CONTROL ECU) Click here

    OK

  6. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL RELAY BLOCK - UREA PUMP CONTROL ECU)


    1. Remove the DCU relay from the instrument panel relay block.

    2. Disconnect the urea pump control ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      DCU relay terminal 3 - A45-11 (+BSU1) Always Below 1 Ω
      DCU relay terminal 3 - A45-10 (+BSU2) Always Below 1 Ω
      DCU relay terminal 3 - A45-19 (+BSU3) Always Below 1 Ω
      DCU relay terminal 3 - A45-1 (+BSU4) Always Below 1 Ω
      DCU relay terminal 3 - A45-2 (+BSU5) Always Below 1 Ω
      DCU relay terminal 2 - Body ground Always Below 1 Ω
      DCU relay terminal 3 or A45-11 (+BSU1) - Body ground and other terminals Always 10 kΩ or higher
      DCU relay terminal 3 or A45-10 (+BSU2) - Body ground and other terminals Always 10 kΩ or higher
      DCU relay terminal 3 or A45-19 (+BSU3) - Body ground and other terminals Always 10 kΩ or higher
      DCU relay terminal 3 or A45-1 (+BSU4) - Body ground and other terminals Always 10 kΩ or higher
      DCU relay terminal 3 or A45-2 (+BSU5) - Body ground and other terminals Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS AND CONNECTOR

    OK

    REPAIR OR REPLACE HARNESS AND CONNECTOR (INSTRUMENT PANEL RELAY BLOCK - BATTERY)

  7. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL RELAY BLOCK - UREA PUMP CONTROL ECU)


    1. Remove the DCU relay from the instrument panel relay block.

    2. Disconnect the urea pump control ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      DCU relay terminal 1- A45-9 (UREL) Always Below 1 Ω
      DCU relay terminal 1 or A45-9 (UREL) - Body ground and other terminals Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS AND CONNECTOR

    OK

    REPLACE UREA PUMP CONTROL ECU Click here