FRONT WIPER MOTOR REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. REMOVE FRONT WIPER ARM HEAD CAP


    1. A01LFCCC01
      B00692L Protective Tape

      Using a screwdriver, detach the claw and remove the front wiper arm head cap.

      Tech Tips


      • Tape the screwdriver tip before use.

      • Use the same procedure for both front wiper arm head caps.

  2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    1. A01LED7

      Remove the nut and front wiper arm and blade assembly LH.

  3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    1. A01LAUF

      Remove the nut and front wiper arm and blade assembly RH.

  4. REMOVE FENDER APRON MUDGUARD SEAL SUB-ASSEMBLY LH


    1. A01L8EZC01
      *a Claw A

      Detach the clip and disconnect the hood to cowl top seal from the fender apron mudguard seal sub-assembly LH.

    2. Detach claw A by hand from the bottom of the fender apron mudguard seal sub-assembly LH.

    3. Detach the claw and clip and remove the fender apron mudguard seal sub-assembly LH.

  5. REMOVE FENDER APRON MUDGUARD SEAL SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  6. REMOVE HOOD TO FRONT FENDER SEAL LH (w/ Seal)


    1. A01LBEZ

      Detach the claw and remove the hood to front fender seal LH.

  7. REMOVE HOOD TO FRONT FENDER SEAL RH (w/ Seal)

    Tech Tips

    Use the same procedure described for the LH side.

  8. REMOVE FRONT FENDER TO COWL SIDE SEAL LH


    1. A01L8KXC01
      B0069FO Remove in this Direction (1)
      B0068NX Remove in this Direction (2)

      Detach the claw and guide and remove the front fender to cowl side seal LH as shown in the illustration.

  9. REMOVE FRONT FENDER TO COWL SIDE SEAL RH

    Tech Tips

    Use the same procedure described for the LH side.

  10. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    1. A01LAFO

      Remove the 2 clips.

    2. A01LDLGC01
      B0069FO Remove in this Direction

      Detach the claw.

    3. A01LADEC01
      B0069FO Remove in this Direction

      Pull the cowl top ventilator louver sub-assembly as shown in the illustration to detach the guide and remove the cowl top ventilator louver sub-assembly.

  11. REMOVE HOOD TO COWL TOP SEAL


    1. A01L9NM

      Detach the claw and clip and remove the hood to cowl top seal.

  12. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

    Note

    Be careful not to damage the windshield when removing the windshield wiper motor and link assembly.


    1. A01LDUVC02
      *1 Motor Grommet
      B0068HS Connector
      B006964 Bolt
      B0069FO Remove in this Direction

      Disconnect the connector.

    2. Remove the 2 bolts.

    3. Detach the motor grommet as shown in the illustration and remove the windshield wiper motor and link assembly.

  13. REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY


    1. A01LA24C01
      B00692L Protective Tape
      B0069FO Remove in this Direction

      Using a screwdriver, disconnect the No. 1 windshield wiper link rod from the front wiper crank pivot.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01LDB3

      Using a T30 "TORX" socket wrench, remove the 2 bolts and windshield wiper motor assembly.