СИСТЕМА ECD, Diagnostic DTC:P0087, P0190, P0192, P0193

DTC Code	DTC Name
P0087	Fuel Rail / System Pressure - Too Low
P0190	Fuel Rail Pressure Sensor Circuit
P0192	Fuel Rail Pressure Sensor Circuit Low Input
P0193	Fuel Rail Pressure Sensor Circuit High Input

DESCRIPTION

The ECM monitors the internal fuel pressure of the common rail using the fuel pressure sensor, and controls the pre-stroke control valve to regulate the internal pressure so that it reaches the target pressure. The pressure sensor is a semiconductor that varies electrical resistance when pressure is applied to its silicon chip. This sensor outputs a voltage in proportion to the internal fuel pressure.

P0087
DTC Detection Drive Pattern	DTC Detection Condition	Trouble Area
After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds	Fuel pressure sensor output voltage stays at fixed value a certain number of times (0.1 seconds or more). (1 trip detection logic)	Open or short in fuel pressure sensor circuit Fuel pressure sensor (common rail assembly) Ran out of fuel Fuel frozen ECM

P0190
DTC Detection Drive Pattern	DTC Detection Condition	Trouble Area
Ignition switch ON for 1 second	Fuel pressure sensor output voltage is 0.55 V or less, or 4.9 V or higher for 0.5 seconds. (1 trip detection logic)	Open or short in fuel pressure sensor circuit Fuel pressure sensor (common rail assembly) ECM Tech Tips Trouble areas are related to the electrical system only (pumps are not involved)

P0192
DTC Detection Drive Pattern	DTC Detection Condition	Trouble Area
Ignition switch ON for 1 second	Fuel pressure sensor output voltage is 0.55 V or less for 0.5 seconds. (1 trip detection logic)	Open or short in fuel pressure sensor circuit Fuel pressure sensor (common rail assembly) ECM Tech Tips Trouble areas are related to the electrical system only (pumps are not involved)

P0193
DTC Detection Drive Pattern	DTC Detection Condition	Trouble Area
Ignition switch ON for 1 second	Fuel pressure sensor output voltage is 4.9 V or higher for 0.5 seconds. (1 trip detection logic)	Open or short in fuel pressure sensor circuit Fuel pressure sensor (common rail assembly) ECM Tech Tips Trouble areas are related to the electrical system only (pumps are not involved)

Related Data List
DTC No.	Data List
P0087 P0190 P0192 P0193	Common Rail Pressure Target Common Rail Pressure

Tech Tips

Check Common Rail Pressure and compare it to Target Common Rail Pressure in the Data List by entering the following menus: Powertrain / Engine and ECT / Data List / Common Rail Pressure, Target Common Rail Pressure. Under stable conditions, the difference between Common Rail Pressure and Target Common Rail Pressure is 5000 kPa or less.
For more information on the fuel pressure sensor and common rail system, refer to System Description Click here.
If DTC P0087 is stored, the following symptoms may appear:

Black smoke
Poor drivability
Lack of power
Lack of power due to accelerator restriction performed by fail-safe function

If DTC P0190, P0192 and/or P0193 is stored, the following symptom may appear:

Lack of power due to accelerator restriction performed by fail-safe function

If DTC P0190, P0192 and/or P0193 is stored, "Common Rail Pressure" always displays 0 kPa or 240000 kPa.

MONITOR DESCRIPTION

P0087 (Fuel pressure sensor output stays at fixed value):

Under normal conditions, the internal fuel pressure of the common rail assembly usually fluctuates by 1000 to 2000 kPa (10 to 20 kgf/cm², 145 to 290 psi) even when driving conditions are constant. This DTC is stored if there is no fluctuation of the fuel pressure. The internal fuel pressure is approximately 30000 to 50000 kPa (306 to 510 kgf/cm², 4350 to 7250 psi) when idling, and it increases to approximately 80000 to 110000 kPa (816 to 1122 kgf/cm², 11600 to 15950 psi) when running the engine at 3000 rpm.

If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The ECM continues operating in fail-safe mode until the ignition switch off.
The diagram below indicates that fuel pressure rises as engine speed increases, but for the malfunction indicated by this DTC, that does not happen.
Even if the system is normal, DTCs may be stored due to a drop in the fuel pressure after running out of fuel, etc. If DTCs P0087 and P1603 are both stored, clear these DTCs and perform a DTC check again.

P0190, P0192 and P0193 (Open or short in fuel pressure sensor circuit):

These DTCs are stored if the fuel pressure sensor output voltage is out of the standard range due to an open or short malfunction of the sensor circuit.

If these DTCs are stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch off.

WIRING DIAGRAM

INSPECTION PROCEDURE

Note

After replacing the ECM, the new ECM needs registration Click here and initialization Click here.

Tech Tips

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE

CHECK DTC OUTPUT

Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Read the DTCs.

Result
Result	Proceed to
DTC P0190, P0192 or P0193 is output	A
DTC P0087 is output*	B

Tech Tips

*: If DTCs P0087 and P1603 are stored, these DTCs may have been stored due to a drop in the fuel pressure after running out of fuel, etc. Therefore, clear these DTCs and perform a DTC check to confirm whether they are output again.

REPLACE COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR) Click here

CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)

Text in Illustration

*a
Front view of wire harness connector

(to Fuel Pressure Sensor)

Disconnect the fuel pressure sensor connector.

Text in Illustration
*a	Front view of wire harness connector (to Fuel Pressure Sensor)

Measure the voltage according to the value(s) in the table below.

Standard Voltage

Tester Connection	Switch Condition	Specified Condition
D69-6 (VC) - D69-4 (E2)	Ignition switch ON	4.5 to 5.5 V
D69-1 (VCS) - D69-3 (E2S)	Ignition switch ON	4.5 to 5.5 V

Reconnect the fuel pressure sensor connector.

REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

Disconnect the fuel pressure sensor connector.
Disconnect the ECM connector.

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
D69-5 (PR) - D134-91 (PCR1)	Always	Below 1 Ω
D69-2 (PR2) - D134-108 (PCR2)	Always	Below 1 Ω
D69-1 (VCS) - D134-140 (VCS)	Always	Below 1 Ω
D69-6 (VC) - D134-93 (VCM)	Always	Below 1 Ω
D69-4 (E2) - D134-92 (E2M)	Always	Below 1 Ω
D69-3 (E2S) - D134-107 (E2S)	Always	Below 1 Ω
D69-5 (PR) or D134-91 (PCR1) - Body ground and other terminals	Always	Below 1 Ω
D69-2 (PR2) or D134-108 (PCR2) - Body ground and other terminals	Always	Below 1 Ω
D69-1 (VCS) or D134-140 (VCS) - Body ground and other terminals	Always	Below 1 Ω
D69-6 (VC) or D134-93 (VCM) - Body ground and other terminals	Always	Below 1 Ω
D69-4 (E2) or D134-92 (E2M) - Body ground and other terminals	Always	Below 1 Ω
D69-3 (E2S) or D134-107 (E2S) - Body ground and other terminals	Always	Below 1 Ω

Reconnect the fuel pressure sensor connector.
Reconnect the ECM connector.

REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

CHECK ECM (CHECK RESISTANCE)

Text in Illustration

*a
Front view of wire harness connector

(to Fuel Pressure Sensor)

Disconnect the fuel pressure sensor connector.

Text in Illustration
*a	Front view of wire harness connector (to Fuel Pressure Sensor)

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
D69-6 (VC) - D69-5 (PR)	Ignition switch off	No short or no open circuit
D69-5 (PR) - D69-4 (E2)	Ignition switch off	No short or no open circuit
D69-1 (VCS) - D69-2 (PR2)	Ignition switch off	No short or no open circuit
D69-2 (PR2) - D69-3 (E2S)	Ignition switch off	No short or no open circuit

Reconnect the fuel pressure sensor connector.

REPLACE COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR) Click here

REPLACE ECM Click here

REPLACE ECM
1. Replace the ECM Click here.
NEXT
CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here
REPAIR OR REPLACE HARNESS OR CONNECTOR
1. Repair or replace the harness or connector.
NEXT
CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here
REPLACE COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
1. Replace the common rail assembly Click here.
NEXT
BLEED AIR FROM FUEL SYSTEM
1. Bleed the air from the fuel system Click here.
NEXT
CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
1. Connect the GTS to the DLC3.
2. Clear the DTCs Click here.
3. Turn the ignition switch off for 30 seconds or more.
4. Turn the ignition switch to ON and turn the GTS on.
5. Let the engine idle for 60 seconds, and then quickly increase the engine speed to 2500 rpm repeatedly for 30 seconds.
6. Confirm that the DTC is not output again.
  
  Tech Tips
  
  Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  2. Input DTC P0087, P0190, P0192 and/or P0193.
  3. Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, increase the idling time.
NEXT

END