ELECTRONIC SHIFT LEVER SYSTEM(for V35A-FTS), Diagnostic DTC:P085011, P085015

DTC Code DTC Name
P085011 Park/Neutral Switch Circuit Short to Ground
P085015 Park/Neutral Switch Circuit Short to Battery or Open

DESCRIPTION

Instead of having a parking position as one of the positions as on a conventional shift lever, a P position switch (shift position indicator) is provided independently under the shift lever. The switch is a momentary type, in which the button does not lock mechanically.

The P position switch (shift position indicator) contains resistors R1, R2, R3 and R4. When the P position switch (shift position indicator) is not pressed, the switch provides a combined resistance of R3 and R4; and when the P position switch (shift position indicator) is pressed, the switch provides a combined resistance of R1, R2, R3 and R4. The voltage at the P1 terminal of the shift control ECU varies with the changes in the resistance of the switch. The shift control ECU determines the P position switch (shift position indicator) operation according to this resistance signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P085011 Park/Neutral Switch Circuit Short to Ground

1. 0.5 seconds or more elapse after engine started with battery voltage 10 V or higher, P1 terminal voltage of P position switch circuit is continuously lower than specified value for 2 seconds or more

(1 trip detection logic)

  • P position switch (shift position indicator)

  • Shift control ECU

  • Wire harness or connector

 Does not come on

  • Master Warning Light


    • Comes on

  • Multi-information Display Error Message


    • Displayed
P085015 Park/Neutral Switch Circuit Short to Battery or Open

1. 0.5 seconds or more elapse after engine started with battery voltage 10 V or higher, P1 terminal voltage of P position switch circuit is continuously higher than specified value for 2 seconds or more

(1 trip detection logic)

  • P position switch (shift position indicator)

  • Shift control ECU

  • Wire harness or connector

 Does not come on

  • Master Warning Light


    • Comes on

  • Multi-information Display Error Message


    • Displayed
Related Data List
DTC No. Data List
P085011

  • P Position Switch Terminal Voltage (Gear Shift Control Module)*

  • BATT Voltage for Gear Shift Control Module

  • Shift Switch Status (N, P Position)
P085015

*: While the P position switch (shift position indicator) is being pushed, the value for Data List item "P Position Switch Terminal Voltage (Gear Shift Control Module)" will decrease.

CONFIRMATION DRIVING PATTERN

Tech Tips

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the All Readiness check procedure.

Click here


  1. Start the engine.

  2. Depress the brake pedal and move the shift lever to select neutral (N).

  3. Push the P position switch (shift position indicator) to select park (P).

WIRING DIAGRAM

B006A1TE03
*1 P Position Switch (Shift Position Indicator)
*2 Shift Control ECU

CAUTION / NOTICE / HINT

Note

The vehicle is equipped with a sub-battery. Therefore, ensure there is no power being supplied to the vehicle when disconnecting or reconnecting the connector of the shift control ECU and when removing or installing the shift control ECU.

Click here

PROCEDURE


  1. INSPECT P POSITION SWITCH (SHIFT POSITION INDICATOR)


    1. B006C7ZC06
      *a

      Component without harness connected

      (P Position Switch (Shift Position Indicator))

      Disconnect the G46 P position switch (shift position indicator) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G46-14 (S) - G46-12 (E) Switch being pressed 613 to 751 Ω
      G46-14 (S) - G46-12 (E) Switch released 3.9 to 4.9 kΩ

    3. Reconnect the G46 P position switch (shift position indicator) connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE P POSITION SWITCH (SHIFT POSITION INDICATOR) Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - P POSITION SWITCH (SHIFT POSITION INDICATOR))


    1. Disconnect the G82 shift control ECU connector.

    2. Disconnect the G46 P position switch (shift position indicator) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      G82-10 (P1) - G46-14 (S) Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      G82-10 (P1) or G46-14 (S) - Body ground and other terminals Always 10 kΩ or higher

    4. Reconnect the G46 P position switch (shift position indicator) connector.

    5. Reconnect the G82 shift control ECU connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (P POSITION SWITCH (SHIFT POSITION INDICATOR) - BODY GROUND)


    1. Disconnect the G46 P position switch (shift position indicator) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      G46-12 (E) - Body ground Always Below 1 Ω

    3. Reconnect the G46 P position switch (shift position indicator) connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE SHIFT CONTROL ECU Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR