CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM(for 8NR-FTS)

CAUTION / NOTICE / HINT

PROCEDURE

1. VEHICLE BROUGHT TO WORKSHOP

   Result

   Proceed to
   NEXT

   NEXT

2. CUSTOMER PROBLEM ANALYSIS

   Click hereClick hereClick here

   Result

   Proceed to
   NEXT

   NEXT

3. INSPECT BATTERY VOLTAGE

   1. Measure the battery voltage.

      Standard Voltage

      11 to 14 V

      Tip:

      If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

   Result

   Proceed to
   NEXT

   NEXT

4. CHECK CAN COMMUNICATION SYSTEM*

   1. Using the GTS, check if the CAN communication system is functioning normally.

      CAN Bus Check

   Tip:

   • Refer to CAN Bus Check in CAN Communication System.

     w/o Central Gateway ECU:Click hereClick hereClick here

     w/ Central Gateway ECU:Click hereClick here

   • The ECM is connected to the CAN communication system. Therefore, before starting troubleshooting, make sure to check that there are no malfunctions in the CAN communications system.

   Result

   Result	Proceed to
   CAN communication system DTCs are not output.	A
   CAN communication system DTCs are output.	B

   B

   GO TO CAN COMMUNICATION SYSTEM

   w/o Central Gateway ECU:Click here

   w/ Central Gateway ECU:Click here

   A

5. CHECK AND CLEAR DTCS AND FREEZE FRAME DATA*

   1. Refer to DTC Check/Clear.

      Click here

   Result

   Proceed to
   NEXT

   NEXT

6. SELECT CHECK MODE DIAGNOSIS*

   1. Refer to Check Mode Procedure.

      Click here

   Result

   Proceed to
   NEXT

   NEXT

7. CHECK FOR DTC*

   1. Proceed to DTC Check/Clear.

      Click here

      Powertrain > Transmission > Trouble Codes

   Result

   Result	Proceed to
   DTCs are not output.	A
   DTCs are output.	B

   B

   DIAGNOSTIC TROUBLE CODE CHARTClick here

   A

8. BASIC INSPECTION

   1. Refer to Continuously Variable Transaxle Fluid.

      Click hereClick here

   2. Refer to Park/Neutral Position Switch.

      Click here

   3. Refer to Shift Lever.

      Click here

   Result

   Proceed to
   OK
   NG

   NG

   COMPONENT INSPECTIONClick here

   OK

9. PROBLEM SYMPTOMS CONFIRMATION

   1. Refer to Road Test.

      Click here

   2. Refer to Mechanical System Tests.

      Click here

   3. Refer to Hydraulic Test.

      Click here

   Result

   Result	Proceed to
   Symptom does not occur	A
   Symptom occurs	B

   B

   COMPONENT INSPECTIONClick here

   A

10. SYMPTOM SIMULATION

    1. Refer to Symptom Simulation.

       Click hereClick hereClick here

    Result

    Proceed to
    NEXT

    NEXT

11. COMPONENT INSPECTION

    Result

    Proceed to
    NEXT

    NEXT

12. REPAIR OR REPLACE

    Result

    Proceed to
    NEXT

    NEXT

13. CONFIRMATION TEST

    Result

    Proceed to
    NEXT

    NEXT

    END

14. DIAGNOSTIC TROUBLE CODE CHART

    1. Proceed to Diagnostic Trouble Code Chart.

       Click hereClick here

    Result

    Proceed to
    NEXT

    NEXT

15. CIRCUIT INSPECTION*

    Result

    Proceed to
    NEXT

    NEXT

16. IDENTIFICATION OF PROBLEM

    Result

    Proceed to
    NEXT

    NEXT

17. REPAIR OR REPLACE

    Result

    Proceed to
    NEXT

    NEXT

18. CONFIRMATION TEST

    Result

    Proceed to
    NEXT

    NEXT

    END