STARTER (for 2.7 kW Type) INSPECTION


  1. INSPECT STARTER ARMATURE ASSEMBLY


    1. B007QXQE01

      Using an ohmmeter, check that there is continuity between the segments of the commutator.

      If there is no continuity between any segment, replace the starter armature.

    2. B007UB3E01

      Using an ohmmeter, check the resistance between the commutator and armature coil core.

      Standard resistance
      10 kΩ or higher

      If the result is not as specified, replace the starter armature.

    3. B007W4W

      Check for the commutator circuit runout.


      1. Place the commutator on V-blocks.

      2. Using a dial indicator, measure the circle runout.

        Maximum runout
        0.05 mm (0.002 in.)

        If the runout is greater than the maximum, replace the starter armature.

    4. B007QHZ

      Using vernier calipers, measure the commutator diameter.

      Standard diameter
      36.0 mm (1.417 in.)
      Minimum diameter
      35.0 mm (1.378 in.)

      If the diameter is less than the minimum, replace the starter armature.

    5. B007UE7

      Check that the undercut portion between the segments is free of foreign objects and measure its depth.

      Standard undercut depth
      0.7 mm (0.028 in.)
      Minimum undercut depth
      0.2 mm (0.008 in.)

      If the undercut depth is less than the minimum, correct it with a hacksaw blade.

  2. INSPECT STARTER YOKE ASSEMBLY


    1. B007VNTE01

      Using an ohmmeter, check that there is continuity between the terminal C wire and brushes.

      If there is no continuity, replace the starter yoke assembly.

    2. B007UDRE01

      Using an ohmmeter, check the resistance between the starter yoke body and brushes.

      Standard resistance
      10 kΩ or higher

      If the result is not as specified, replace the starter yoke.

  3. INSPECT STARTER BRUSH HOLDER ASSEMBLY


    1. B007R3KE01

      Using vernier calipers, measure the brush length.

      Standard length
      20.5 mm (0.807 in.)
      Minimum length
      11.0 mm (0.433 in.)

      If the length is less than the minimum, replace the brush holder and starter yoke.

    2. B007U28E01

      Check the pull scale reading as soon as the brush spring is separated from the brush.

      Standard spring load
      26 to 45 N (2.7 to 4.6 kgf, 5.8 to 10.1 lbf)
      Minimum spring load
      12.4 N (1.3 kgf, 2.8 lbf)

      If the spring load is less than the minimum, replace the brush holder assembly.

    3. B007TUDE01

      Using an ohmmeter, measure the resistance between the positive (+) and negative (-) brush holders.

      Standard resistance
      10 kΩ or higher

      If the result is not as specified, repair or replace the brush holder assembly.

  4. INSPECT STARTER CLUTCH SUB-ASSEMBLY


    1. B007T1OE01

      Turn the clutch pinion gear clockwise and check that it turns freely. Try to turn the clutch pinion gear counterclockwise and check that it locks.

      If necessary, replace the starter clutch.

  5. INSPECT MAGNET STARTER SWITCH ASSEMBLY


    1. B007PE8E01

      Using an ohmmeter, check that there is continuity between terminals 50 and C.

      If there is no continuity, replace the magnet starter switch assembly.

    2. B007OZNE01

      Using an ohmmeter, check that there is continuity between terminal 50 and the magnet switch body.

      If there is no continuity, replace the magnet starter switch assembly.