POWER STEERING SYSTEM Drive Mode Select Switch Circuit

DESCRIPTION

The electronic throttle and the EPS character change by the operation of the drive mode select switch (combination switch assembly).

WIRING DIAGRAM

B007XI0E01

PROCEDURE


  1. CHECK THE PROBLEM SYMPTOMS


    1. Check each symptom by checking the suspected areas in the table below.

      Result
      Result Proceed to
      SPORT, SPORT S/S+ mode or NORMAL mode is abnormal. A
      ECO mode is abnormal. B

    B

    GO TO AIR CONDITIONING SYSTEM Click here

    A

  2. CHECK CAN COMMUNICATION SYSTEM


    1. Check for DTCs.

      Click here

      Result
      Result Proceed to
      CAN communication system DTCs are not output. A
      CAN communication system DTCs are output. B

    B

    GO TO CAN COMMUNICATION SYSTEM Click here

    A

  3. CHECK HARNESS AND CONNECTOR (DRIVE MODE SELECT SWITCH (COMBINATION SWITCH ASSEMBLY) - BODY GROUND)


    1. Turn the engine switch off.

    2. B007Y7IC10
      *a

      Front view of wire harness connector

      (to Drive mode select switch (combination switch assembly))

      Disconnect the J35 drive mode select switch (combination switch assembly) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J35-1 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT DRIVE MODE SELECT SWITCH (COMBINATION SWITCH ASSEMBLY)


    1. Inspect drive mode select switch (combination switch assembly).

      for U661E: Click here

      for U661F: Click here

      for U881E: Click here

      for U881F: Click here

      OK
      Drive mode select switch (combination switch assembly) is normal.
      Result
      Result Proceed to
      OK (for 8AR-FTS) A
      OK (for 2GR-FKS) B
      NG C

    B

    CHECK HARNESS AND CONNECTOR (DRIVE MODE SELECT SWITCH (COMBINATION SWITCH ASSEMBLY) - ECM) Click here

    C

    REPLACE DRIVE MODE SELECT SWITCH (COMBINATION SWITCH ASSEMBLY) for U661E: Click here
    REPLACE DRIVE MODE SELECT SWITCH (COMBINATION SWITCH ASSEMBLY) for U661F: Click here
    REPLACE DRIVE MODE SELECT SWITCH (COMBINATION SWITCH ASSEMBLY) for U881E: Click here
    REPLACE DRIVE MODE SELECT SWITCH (COMBINATION SWITCH ASSEMBLY) for U881F: Click here

    A

  5. CHECK HARNESS AND CONNECTOR (DRIVE MODE SELECT SWITCH (COMBINATION SWITCH ASSEMBLY) - ECM)


    1. Reconnect the J35 drive mode select switch (combination switch assembly) connector.

    2. B007Y0WC08
      *a

      Rear view of wire harness connector

      (to ECM)

      Disconnect the A46 ECM connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A46-36 (PWMS) - Body ground SPORT mode switch being turned and held Below 50 Ω
      A46-36 (PWMS) - Body ground SPORT mode switch not turned 10 kΩ or higher
      A46-39 (SPCN) - Body ground NORMAL mode switch being pushed and held Below 50 Ω
      A46-39 (SPCN) - Body ground NORMAL mode switch not pushed 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. CHECK HARNESS AND CONNECTOR (DRIVE MODE SELECT SWITCH (COMBINATION SWITCH ASSEMBLY) - ECM)


    1. Reconnect the J35 drive mode select switch (combination switch assembly) connector.

    2. B007Y0WC09
      *a

      Rear view of wire harness connector

      (to ECM)

      Disconnect the A37 ECM connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A37-55 (PWMS) - Body ground SPORT mode switch being turned and held Below 50 Ω
      A37-55 (PWMS) - Body ground SPORT mode switch not turned 10 kΩ or higher
      A37-40 (SPCN) - Body ground NORMAL mode switch being pushed and held Below 50 Ω
      A37-40 (SPCN) - Body ground NORMAL mode switch not pushed 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR