WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) Only Wireless Control Function is Inoperative

DTC Code DTC Name
Only Wireless Control Function is Inoperative

DESCRIPTION

The door control receiver receives signals from the door control transmitter assembly and sends these signals to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then controls all doors by sending lock/unlock signals to each door, and sends hazard flasher signals to the combination meter assembly.

WIRING DIAGRAM

  1. for Sedan without Tire Pressure Warning System or except Sedan

    B290776E06

  2. for Sedan with Tire Pressure Warning System

    B352738E01

CAUTION / NOTICE / HINT

Note:

  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, wireless function performance may be affected.

  • When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.*

  • It is necessary to perform initializationClick hereafter registrationClick hereof the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.*

    • *: w/ Tire Pressure Warning System

PROCEDURE

  1. SYSTEM CHECK

    1. Check the vehicle specification.

    Result

    Result

    Proceed to

    w/ Tire Pressure Warning System

    A

    w/o Tire Pressure Warning System

    B
    B

    CHECK POWER DOOR LOCK OPERATIONClick here

    A

  2. CHECK FOR DTC (TIRE PRESSURE WARNING SYSTEM)

    1. Clear the DTCs.

    2. Recheck for DTCs.

      Body Electrical > Entry&Start > Trouble Codes

    Result

    Result

    Proceed to

    DTCs are not output

    A

    DTCs are output

    B
    A

    CHECK POWER DOOR LOCK OPERATIONClick here

    B

    GO TO TIRE PRESSURE WARNING SYSTEM

    Click here

  3. CHECK POWER DOOR LOCK OPERATION

    1. Check the power door lock operation.

      for Sedan:Click here

      for Hatchback, Wagon:Click here

      OK

      Locked doors unlock

    Result

    Proceed to

    OK

    NG
    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM

    for Sedan:Click here

    for Hatchback, Wagon:Click here

    OK

  4. CHECK KEY REMINDER WARNING SYSTEM

    1. Check that the key reminder warning buzzer operates properly.

      Click here

      OK

      Key reminder warning buzzer operates properly.

    Result

    Proceed to

    OK

    NG
    NG

    GO TO KEY REMINDER WARNING SYSTEM

    Click here

    OK

  5. CHECK DOOR CONTROL TRANSMITTER ASSEMBLY

    1. When a known good registered door control transmitter assembly is used, check that the wireless functions operate properly.

    Result

    Result

    Proceed to

    Wireless door lock/unlock/back door open function operates properly with a known good door control transmitter assembly.

    A

    Wireless door lock/unlock/back door open function does not operate.

    B
    B

    CHECK WAVE ENVIRONMENTClick here

    A

  6. CHECK TRANSMITTER BATTERY (VOLTAGE)

    1. Inspect the battery capacity.

      1. Remove the battery from the door control transmitter assembly that does not operate (Click here). Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative (-) terminal.

        Note:

        Do not wrap the lead wire around a terminal, wedge it between the terminals, or solder it. A terminal may be deformed or damaged, and the battery will not be able to be installed correctly.

    2. B338575

      Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.

      Note:

      When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter assembly from being damaged.

    3. B338576

      Check the transmitter battery voltage.

      Tip:

      Measure the transmitter battery voltage while pressing the lock or unlock switch on the door control transmitter assembly.

      Standard Voltage

      Item

      Content

      Tester Connection

      Transmitter battery positive (+) - Transmitter battery negative (-)

      Condition

      Ignition switch off, all doors closed and lock or unlock switch is pressed

      Specified Condition

      2.5 to 3.2 V

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE DOOR CONTROL TRANSMITTER ASSEMBLY

    NG

    REPLACE TRANSMITTER BATTERY

    Click here

  7. CHECK WAVE ENVIRONMENT

    1. Bring the door control transmitter assembly near the door control receiver, and perform a wireless operation check.

      Tip:

      • When the door control transmitter assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

      • If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

      OK

      Wireless functions operate properly.

    Result

    Proceed to

    OK

    NG
    OK

    END (AFFECTED BY WAVE INTERFERENCE)

    NG

  8. SWITCH TO SELF-DIAGNOSTIC MODE (USING GTS)

    1. Connect the GTS to the DLC3.

    2. Turn the Ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Wireless Diagnosis Mode.

      Body Electrical > Main Body > Utility

      Tester Display

      Wireless Code Registration

    5. Proceed to the next step in accordance with the prompts on the GTS screen.

    6. B220865E28

      Check that the system has switched to self-diagnostic mode by checking the interior light output pattern.

    Result

    Proceed to

    NEXT
    NEXT

  9. CHECK SELF DIAGNOSTIC MODE

    1. Inspect the diagnostic outputs when the door control transmitter assembly switch is pressed. The diagnostic outputs can be checked by the flash patterns of the interior lights.

      B163380E93

    Result

    Result

    Proceed to

    Normal wave (light flash pattern and buzzer pattern) is output.

    A

    Unmatching recognition code is output.

    B

    No diagnostic outputs.

    C
    A

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

    for LHD:Click here

    for RHD:Click here

    C

    CHECK DOOR CONTROL RECEIVER (RESPONSE)Click here

    B

  10. CHECK REGISTER RECOGNITION CODE

    1. Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.

      Click here

      OK

      Recognition code can be registered.

    Result

    Result

    Proceed to

    OK

    A

    NG (w/ Tire Pressure Warning System)

    B

    NG (w/o Tire Pressure Warning System)

    C
    A

    END (GO TO OPERATION CHECK)

    B

    REPLACE DOOR CONTROL RECEIVERClick here

    C

    REPLACE DOOR CONTROL RECEIVERClick here

  11. CHECK DOOR CONTROL RECEIVER (RESPONSE)

    1. Prepare the door control transmitter assembly from another vehicle.

    2. Press and hold down the door control transmitter assembly switch.

    3. Check that an unmatching recognition code is output.

      OK

      Unmatching recognition code is output.

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE DOOR CONTROL TRANSMITTER ASSEMBLY

    NG

  12. CHECK DOOR CONTROL RECEIVER (+B, GND)

    1. B281165C02

      *a

      Front view of wire harness connector

      (to Door Control Receiver)

      Disconnect the L34 door control receiver.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      L34-1 (GND) - Body ground

      Always

      Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      L34-5 (+B) - Body ground

      Always

      11 to 14 V

    Result

    Result

    Proceed to

    OK (w/ Tire Pressure Warning System)

    A

    OK (w/o Tire Pressure Warning System)

    B

    NG

    C
    B

    CHECK DOOR CONTROL RECEIVER (OUTPUT)Click here

    C

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    A

  13. CHECK DOOR CONTROL RECEIVER (OUTPUT)

    1. Connect the L34 door control receiver connector.

    2. B281169C02

      *a

      Component with harness connected

      (Door Control Receiver)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      L34-2 (RDA) - Body ground

      Ignition switch off, all doors closed and door control transmitter assembly switch not pressed

      11 to 14 V

      Ignition switch off, all doors closed and door control transmitter assembly switch pressed

      Pulse generation

      (0 to 12 V)

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE DOOR CONTROL RECEIVER

    for Sedan:Click here

    for Hatchback:Click here

    for Wagon:Click here

    OK

  14. CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - DOOR CONTROL RECEIVER)

    1. Disconnect the L70 tire pressure warning ECU and receiver connector.

    2. Disconnect the L34 door control receiver connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      L34-2 (RDA) - L70-10 (RDA3)

      Always

      Below 1 Ω

      L34-3 (PRG) - L70-9 (PRG3)

      Always

      Below 1 Ω

      L34-2 (RDA) - Body ground

      Always

      10 kΩ or higher

      L34-3 (PRG) - Body ground

      Always

      10 kΩ or higher

      L70-10 (RDA3) - Body ground

      Always

      10 kΩ or higher

      L70-9 (PRG3) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  15. REPLACE DOOR CONTROL RECEIVER

    1. Temporarily replace the door control receiver with a new or known good one.

      for Sedan:Click here

      for Hatchback:Click here

      for Wagon:Click here

    Result

    Proceed to

    NEXT
    NEXT

  16. CHECK REGISTER RECOGNITION CODE

    1. Perform the Registration procedure.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

  17. CHECK DOOR CONTROL RECEIVER (OPERATION)

    1. Check that the doors can be locked and unlocked by the door control transmitter assembly lock and unlock switches.

      OK

      Doors can be locked and unlocked by the door control transmitter assembly.

    Result

    Proceed to

    OK

    NG
    OK

    END (DOOR CONTROL RECEIVER WAS DEFECTIVE)

    NG

    REPLACE TIRE PRESSURE WARNING ECU

    Click here

  18. CHECK DOOR CONTROL RECEIVER (OUTPUT)

    1. Connect the L34 door control receiver connector.

    2. B281169C02

      *a

      Component with harness connected

      (Door Control Receiver)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      L34-2 (RDA) - Body ground

      Ignition switch off, all doors closed and door control transmitter assembly switch not pressed

      11 to 14 V

      Ignition switch off, all doors closed and door control transmitter assembly switch pressed

      Pulse generation

      (0 to 12 V)

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE DOOR CONTROL RECEIVER

    for Sedan:Click here

    for Hatchback:Click here

    for Wagon:Click here

    OK

  19. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - DOOR CONTROL RECEIVER)

    1. Disconnect the E22 main body ECU (multiplex network body ECU) connector.

    2. Disconnect the L34 door control receiver connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      L34-2 (RDA) - E22-16 (RDA)

      Always

      Below 1 Ω

      L34-3 (PRG) - E22-4 (PRG)

      Always

      Below 1 Ω

      L34-2 (RDA) - Body ground

      Always

      10 kΩ or higher

      L34-3 (PRG) - Body ground

      Always

      10 kΩ or higher

      E22-16 (RDA) - Body ground

      Always

      10 kΩ or higher

      E22-4 (PRG) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  20. REPLACE DOOR CONTROL RECEIVER

    1. Temporarily replace the door control receiver with a new or known good one.

      for Sedan:Click here

      for Hatchback:Click here

      for Wagon:Click here

    Result

    Proceed to

    NEXT
    NEXT

  21. CHECK REGISTER RECOGNITION CODE

    1. Perform the Registration procedure.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

  22. CHECK DOOR CONTROL RECEIVER (OPERATION)

    1. Check that the doors can be locked and unlocked by the door control transmitter assembly lock and unlock switches.

      OK

      Doors can be locked and unlocked by the door control transmitter assembly.

    Result

    Proceed to

    OK

    NG
    OK

    END (DOOR CONTROL RECEIVER WAS DEFECTIVE)

    NG

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

    for LHD:Click here

    for RHD:Click here