AMPLIFIER ANTENNA REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during amplifier antenna assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control)

Click here

Pre-collision system
Memorize steering angle neutral point Parking assist monitor system

Click here

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click here

B0084SX

PROCEDURE


  1. PRECAUTION (w/ Rear Seat Side Airbag)

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Rear Seat Side Airbag)

    for 2AR-FE:

    Click here

    for A25A-FKS:

    Click here

    for 2GR-FKS:

    Click here

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    • If an airbag deploys for any reason, it may cause a serious injury.

    B0087PP

  3. REMOVE REAR SEAT ASSEMBLY (for Fixed Seat Type)

    Click here

  4. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Fixed Seat Type)

    Click here

  5. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH (for Fixed Seat Type)

    Tech Tips

    Use the same procedure as for the LH side.

  6. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Fold Down Seat Type)

    Click here

  7. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)

    Click here

  8. REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)

    Click here

  9. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Fold Down Seat Type)

    Click here

  10. REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)

    Click here

  11. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH (for Fold Down Seat Type)

    Tech Tips

    Use the same procedure as for the LH side.

  12. REMOVE REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)

    Tech Tips

    Use the same procedure as for the LH side.

  13. REMOVE REAR SEAT HEADREST ASSEMBLY (for Reclining Seat Type)

    Click here

  14. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Reclining Seat Type)

    Click here

  15. REMOVE REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type)

    Click here

  16. REMOVE REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type)

    Click here

  17. REMOVE REAR SEATBACK COVER (for Reclining Seat Type)

    Click here

  18. REMOVE REAR SEATBACK ASSEMBLY LH (for Reclining Seat Type)

    Click here

  19. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Reclining Seat Type)

    Click here

  20. REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Reclining Seat Type)

    Click here

  21. REMOVE REAR SEATBACK ASSEMBLY RH (for Reclining Seat Type)

    Click here

  22. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH (for Reclining Seat Type)

    Tech Tips

    Use the same procedure as for the LH side.

  23. REMOVE REAR SIDE SEATBACK ASSEMBLY RH (for Reclining Seat Type)

    Tech Tips

    Use the same procedure as for the LH side.

  24. REMOVE INNER ROOF SIDE GARNISH LH

    Click here

  25. REMOVE INNER ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  26. REMOVE NO. 2 AMPLIFIER ANTENNA ASSEMBLY


    1. B00886K

      Disconnect the 2 connectors.

    2. Remove the bolt.

    3. Disengage the 2 guides to remove the No. 2 amplifier antenna assembly.

  27. REMOVE NO. 1 AMPLIFIER ANTENNA ASSEMBLY

    Tech Tips

    Use the same procedure as for the No. 2 amplifier antenna assembly.

  28. REMOVE ANTENNA CORD SUB-ASSEMBLY


    1. B0086FD

      Disconnect the connector to remove the antenna cord sub-assembly.

      Tech Tips

      Use the same procedure for the RH side and LH side.