DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM FREEZE FRAME DATA

  1. FREEZE FRAME DATA

    1. When a DTC is stored, the 4WD ECU assembly stores the current vehicle state as Freeze Frame Data.

      Tip:

      Freeze Frame Data at the time a DTC is stored:

      • When the 4WD ECU assembly stores data at the time a DTC is stored, no updates will be performed until the data is cleared.

      • "Number of IG ON" is not stored as Freeze Frame Data.

  2. CHECK FREEZE FRAME DATA

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Chassis / Four Wheel Drive / Trouble Codes.

      Chassis > Four Wheel Drive > Trouble Codes

    5. According to the display on the GTS, select the trouble code data display with Freeze Frame Data.

      Chassis > Four Wheel Drive

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      Vehicle Speed

      Maximum wheel speed sensor reading

      Min.: 0 km/h (0 mph)

      Max.: 326 km/h (202 mph)

      Vehicle stopped: 0 km/h (0 mph)

      No large fluctuations when driving at a constant speed.

      Forward and Rearward G

      Forward and rearward G

      Min.: -25.10 m/s2

      Max.: 24.90 m/s2

      -

      Changes in proportion with acceleration during acceleration/deceleration.

      FR Wheel Speed

      Front wheel speed sensor RH reading

      Min.: 0 km/h (0 mph)

      Max.: 326 km/h (202 mph)

      Vehicle stopped: 0 km/h (0 mph)

      No large fluctuations when driving at a constant speed.

      FL Wheel Speed

      Front wheel speed sensor LH reading

      Min.: 0 km/h (0 mph)

      Max.: 326 km/h (202 mph)

      Vehicle stopped: 0 km/h (0 mph)

      No large fluctuations when driving at a constant speed.

      RR Wheel Speed

      Rear wheel speed sensor RH reading

      Min.: 0 km/h (0 mph)

      Max.: 326 km/h (202 mph)

      Vehicle stopped: 0 km/h (0 mph)

      No large fluctuations when driving at a constant speed.

      RL Wheel Speed

      Rear wheel speed sensor LH reading

      Min.: 0 km/h (0 mph)

      Max.: 326 km/h (202 mph)

      Vehicle stopped: 0 km/h (0 mph)

      No large fluctuations when driving at a constant speed.

      Accelerator Opening Angle %

      Accelerator pedal depression amount

      Min.: 0%

      Max.: 127%

      When the accelerator pedal is released: 0%

      Changes in proportion to the movement of the pedal during accelerator pedal operation.

      Real Engine Torque

      Real engine torque

      Min.: -1024 Nm

      Max.: 1023 Nm

      -

      -

      Steering Angle Sensor

      Steering angle sensor

      Min.: - 3276.8°

      Max.: 3276.7°

      Left turn: Increase

      Right turn: Decrease

      -

      IG1 Voltage Value

      IG1 voltage value

      Min.: 0 V

      Max.: 20 V

      Ignition switch ON: 11 to 14 V

      -

      Stop Light SW

      Stop light switch

      ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      -

      Parking Brake SW

      Parking brake switch

      ON or OFF

      OFF: Parking brake released

      ON: Parking brake applied

      -

      Number of IG ON

      Number of operations of ignition switch being turned ON after storing Freeze Frame Data

      0 to 31

      0

      -

      Yaw Rate Sensor

      Yaw rate value

      Min.: -128°/s

      Max.: 127°/s

      w/o VSC:

      • 0°/s

      w/ VSC:

      • Vehicle stopped: 0°/s

      • Turning right: -128 to 0°/s

      • Turning left: 0 to 127°/s

      -

      Lateral G

      Lateral G

      Min.: -25.10 m/s2

      Max.: 24.90 m/s2

      -

      Changes in proportion with the pedal movement speed when the brake pedal is being operated.

  3. CLEAR FREEZE FRAME DATA

    Note:

    Clearing the DTCs will also clear the Freeze Frame Data.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Clear the DTCs and Freeze Frame Data (Click here).