ECD SYSTEM, Diagnostic DTC:P062F

DTC Code DTC Name
P062F Internal Control Module EEPROM Error

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

P062F

Internal Control Module EEPROM Error

When any condition below is met (1 trip detection logic):

  • Injector compensation code is not registered.

  • Wrong injector compensation code is registered.

  • Injector pilot quantity learning value is not registered.

  • Catalyst deterioration learning value is not registered.

  • Crank time compensation learning value is not registered.*1

  • Air fuel ratio sensor compensation learning value is not registered.*1

  • Injector compensation code

  • Injector pilot quantity learning value

  • Catalyst thermal deterioration value

  • Air fuel ratio sensor compensation learning value

  • Crank time compensation learning value

  • ECM

Comes on

DTC stored

*1: When this malfunction occurs, the MIL does not illuminate.

Note:

  • When a injector assembly is replaced, the new injector compensation code must be input into the ECM. When the ECM is replaced, all of the existing injector compensation codes must be input into the new ECM.

  • Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector assembly. If an incorrect injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

  • When a injector assembly is replaced, perform pilot quantity learning. When the ECM is replaced, all of the existing injector pilot quantity learning values must be input into the new ECM.

  • When the catalyst converter is replaced, the new catalyst thermal deterioration value must be input into the ECM. When the ECM is replaced, the existing catalyst thermal deterioration value must be input into the new ECM.

Tip:

When replacing the ECM with a new one, if the injector compensation code, injector pilot quantity learning value and/or catalyst thermal deterioration value are not entered, DTC P062F will be stored.

  1. When replacing the ECM with a new one, input all learning values and codes into the new ECM as follows:

    1. Prior to replacing the ECM, use the GTS to read and save each learning values and codes from the original ECM.

      Click here

    2. After installing a new ECM, input the saved learning values and codes into the new ECM using the GTS.

      Click here

    3. Turn the ignition switch off and turn the GTS off.

    4. Wait for at least 30 seconds.

    5. Turn the ignition switch to ON and turn the GTS on.

    6. Clear the DTC P062F stored in the ECM using the GTS.

      Powertrain > Engine > Clear DTCs

      Tip:

      • Each injector assembly has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the compensation codes to balance the different fuel injections between each injector assembly.

      • When you first turn ON the ignition switch after replacing the ECM and other component(s), DTC P062F is stored. Manually clear the DTC upon completion of compensation code registration.

      Replacement Part

      Utility Item

      ECM

      Exhaust manifold converter sub-assembly (DPF catalyst)

      Catalyst Record Clear

      Click here

      Injector assembly

CONFIRMATION DRIVING PATTERN

DTC No.

DTC Detection Drive Pattern

P062F

Ignition switch ON for 1 second

CAUTION / NOTICE / HINT

Note:

  • After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

  • After replacing the exhaust manifold converter sub-assembly (DPF catalyst), clear the thermal deterioration data stored in the ECM.

    Click here

Tip:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE

  1. PERFORM LEARNING VALUES CONFIRMATION

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

      Note:

      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Confirmation.

      Click here

      Powertrain > Engine > Utility

      Tester Display

      Learning Values Confirmation

      Result

      Result

      Proceed to

      The injector compensation codes are not input

      A

      The injector compensation codes registered in the ECM are different than the codes imprinted on the injector assemblies

      The pilot quantity learning values are set to the default values.

      B

      The catalyst deterioration learning values are set to the default values

      Except above

      C
      Tip:

      • When the catalyst deterioration learning values are set to the default values, "FFFFFFFF" is displayed.

      • When the injector pilot quantity learning values are set to the default values, "7FFF" is displayed.

    B

    PERFORM LEARNING VALUES WRITEClick here

    C

    CHECK DTC OUTPUTClick here

    A

  2. REGISTER INJECTOR COMPENSATION CODE

    1. Register the injector compensation codes.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

    PERFORM PILOT QUANTITY LEARNINGClick here

  3. PERFORM LEARNING VALUES WRITE

    Tip:

    When replacing the ECM, after performing "Learning Values Save" to save the learned values from the old ECM using the GTS and replacing the old ECM with a new one, "Learning Values Write" was not performed using the GTS causing this DTC to be output.

    1. Install the old ECM.

      Click here

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON and turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Save.

      Click here

      Powertrain > Engine > Utility

      Tester Display

      Learning Values Save

    5. Remove the old ECM.

      Click here

    6. Install the new ECM.

      Click here

    7. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Write.

      Click here

      Powertrain > Engine > Utility

      Tester Display

      Learning Values Write

    Result

    Proceed to

    NEXT
    NEXT

  4. PERFORM LEARNING VALUES CONFIRMATION

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

      Note:

      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Confirmation.

      Click here

      Powertrain > Engine > Utility

      Tester Display

      Learning Values Confirmation

      Result

      Result

      Proceed to

      The pilot quantity learning values are set to the default values.

      A

      The catalyst deterioration learning values are set to the default values

      B

      Except above

      C
      Tip:

      • When the catalyst deterioration learning values are set to the default values, "FFFFFFFF" is displayed.

      • When the injector pilot quantity learning values are set to the default values, "7FFF" is displayed.

    B

    REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLYClick here

    C

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

    A

  5. PERFORM PILOT QUANTITY LEARNING

    1. Perform the pilot quantity learning.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

    CHECK DTC OUTPUTClick here

  6. REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

    1. Replace the exhaust manifold converter sub-assembly.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

  7. PERFORM CATALYST RECORD CLEAR

    1. Perform the catalyst record clear.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

  8. CHECK DTC OUTPUT

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs.

      Powertrain > Engine > Clear DTCs

    5. Turn the ignition switch off and leave the vehicle for 30 seconds or more.

    6. Turn the ignition switch to ON for 1 second.

    7. Turn the GTS on.

    8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    9. Read the DTCs.

      Powertrain > Engine > Trouble Codes

      Result

      Result

      Proceed to

      DTC is not output

      A

      DTC P062F is output

      B
    A

    END

    B

  9. REPLACE ECM

    1. Replace the ECM.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

  10. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs.

      Powertrain > Engine > Clear DTCs

    5. Turn the ignition switch off and leave the vehicle for 30 seconds or more.

    6. Turn the ignition switch to ON for 1 second.

    7. Turn the GTS on.

    8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    9. Confirm that the DTC is not output.

      Powertrain > Engine > Trouble Codes

    Result

    Proceed to

    NEXT
    NEXT

    END