AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) Radio Broadcast cannot be Received or Poor Reception

DTC Code DTC Name
Radio Broadcast cannot be Received or Poor Reception

PROCEDURE

  1. CHECK RADIO RECEIVER ASSEMBLY

    1. Check the radio automatic station search function.

      1. Check the radio automatic station search function by activating it.

        Result

        Result

        Proceed to

        Automatic station search function does not stop

        A

        Automatic station search function stops on a station

        B
    B

    REPLACE RADIO RECEIVER ASSEMBLY

    for Sedan:Click hereClick here

    for Hatchback, Wagon:Click here

    A

  2. CHECK OPTIONAL COMPONENTS

    1. Check if any optional components that may decrease reception capacity, such as sunshade film, are installed.

      Result

      Result

      Proceed to

      Optional components are installed

      A

      Optional components are not installed

      B
      Note:

      Do not remove optional components without the permission of the customer.

    A

    REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

    B

  3. CHECK RADIO RECEIVER ASSEMBLY

    1. E187251

      Preparation for check

      1. Disconnect the antenna connector from the radio receiver assembly.

    2. Check for noise

      1. Turn the ignition switch to ACC with the radio receiver assembly connectors connected.

      2. Turn the radio receiver assembly on and enter AM mode.

      3. Place a screwdriver, thin wire or other metal object on the radio receiver assembly antenna jack and check that noise can be heard from the speakers.

        OK

        Noise occurs.

    Result

    Result

    Proceed to

    OK (for Sedan)

    A

    OK (except Sedan)

    B

    NG

    C
    B

    INSPECT RADIO RECEIVER ASSEMBLYClick here

    C

    REPLACE RADIO RECEIVER ASSEMBLY

    for Sedan:Click hereClick here

    for Hatchback, Wagon:Click here

    A

  4. CHECK WINDOW GLASS ANTENNA WIRE

    1. E111994C14

      *a

      Tester Probe

      *b

      Antenna Wire

      *c

      Tin Foil

      Check for continuity in the window glass antenna wire.

      Note:

      When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of each probe and press the foil against the wire with your finger, as shown in the illustration.

      Tip:

      Check for continuity at the center of each antenna wire as shown in the illustration.

      OK

      There is continuity in the window glass antenna wire.

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR WINDOW GLASS ANTENNA WIRE

    Click here

    OK

  5. INSPECT RADIO RECEIVER ASSEMBLY

    1. Disconnect the RA radio receiver assembly connector.

    2. E188455C09

      *a

      Component without harness connected

      (Radio Receiver Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      RA-5 (ANT+) - Body ground

      Ignition switch ACC

      Radio switch on and FM or AM selected

      11 to 14 V

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE RADIO RECEIVER ASSEMBLY

    Click hereClick here

    OK

  6. REPLACE ANTENNA CORD SUB-ASSEMBLY

    1. Replace the antenna cord sub-assembly and check if radio broadcasts can be received normally.

      Click hereClick here

      OK

      Radio broadcasts can be received normally.

    Result

    Proceed to

    OK

    NG
    OK

    END

    NG

  7. REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY

    1. Replace the No. 1 amplifier antenna assembly and check if radio broadcasts can be received normally.

      Click hereClick here

      OK

      Radio broadcasts can be received normally.

    Result

    Proceed to

    OK

    NG
    OK

    END

    NG

    REPLACE RADIO RECEIVER ASSEMBLY

    Click hereClick here

  8. INSPECT RADIO RECEIVER ASSEMBLY

    1. Disconnect the RA radio receiver assembly connector.

    2. E188455C10

      *a

      Component without harness connected

      (Radio Receiver Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      RA-5 (ANT+) - Body ground

      Ignition switch ACC

      Radio switch on and FM or AM selected

      11 to 14 V

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE RADIO RECEIVER ASSEMBLY

    Click here

    OK

  9. REPLACE ANTENNA CORD SUB-ASSEMBLY

    1. Replace the antenna cord sub-assembly and check if radio broadcasts can be received normally.

      for Hatchback: ClickhereClick here

      for Wagon:Click here

      OK

      Radio broadcasts can be received normally.

    Result

    Proceed to

    OK

    NG
    OK

    END

    NG

  10. REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY

    1. Replace the No. 3 antenna cord sub-assembly and check if radio broadcasts can be received normally.

      for Hatchback:Click here

      for Wagon:Click here

      OK

      Radio broadcasts can be received normally.

    Result

    Proceed to

    OK

    NG
    OK

    END

    NG

  11. REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY

    1. Replace the No. 1 amplifier antenna assembly and check if radio broadcasts can be received normally.

      for Hatchback:Click here

      for Wagon:Click here

      OK

      Radio broadcasts can be received normally.

    Result

    Proceed to

    OK

    NG
    OK

    END

    NG

    REPLACE RADIO RECEIVER ASSEMBLY

    Click here