HYBRID CONTROL SYSTEM, Diagnostic DTC:P06B0-163, P06D6-511, P06E6-164, P0A1A-151, P0A1A-166, P0A1A-658, P0A1A-791, P0A1B-198, P0A1B-786, P0A1B-794, P1C2A-155, P1C2B-192, P1C73-512, P1CA6-156, P1CA7-193, P3133-659, P3134-661

DTC Code DTC Name
P06B0-163 Sensor Power Supply "A" Circuit / Open
P06D6-511 Sensor Reference Voltage "F" Circuit / Open
P06E6-164 Sensor Power Supply "C" Circuit / Open
P0A1A-151 Generator Control Module
P0A1A-166 Generator Control Module
P0A1A-658 Generator Control Module
P0A1A-791 Generator Control Module
P0A1B-198 Drive Motor "A" Control Module
P0A1B-786 Drive Motor "A" Control Module
P0A1B-794 Drive Motor "A" Control Module
P1C2A-155 Generator A/D Converter Circuit
P1C2B-192 Drive Motor "A" A/D Converter Circuit
P1C73-512 Sensor Standard Voltage "F" Circuit / Open
P1CA6-156 Generator Control Module Malfunction
P1CA7-193 Drive Motor Control Module Malfunction
P3133-659 Communication Error from Generator to Drive Motor "A"
P3134-661 Communication Error from Drive Motor "A" to Generator

DESCRIPTION

The MG ECU located in the inverter with converter assembly monitors its internal operation and it will set DTCs when it detects malfunctions.

DTC No. INF Code DTC Detection Condition Trouble Area
P06B0 163 IPM positive power source error Inverter with converter assembly
P06D6 511 Standard voltage for analog signal offset error
P06E6 164 IPM negative power source error
P0A1A 151 Run pulse signal cycle deviation or stop

  • Inverter with converter assembly

  • Hybrid battery junction block assembly

  • Service plug grip
166 R/D converter NM stop error Inverter with converter assembly
658 ALU error
791 R/D converter communication error
P0A1B 198 R/D converter NM stop error
786 ALU error
794 R/D converter communication error
P1C2A 155 A/D converter error
P1C2B 192 A/D converter error
P1C73 512 Standard voltage for analog signal error
P1CA6 156 CPU ROM-RAM error
P1CA7 193 CPU ROM-RAM error
P3133 659 Communication error (from MG1 to MG2)

  • Inverter with converter assembly

  • Hybrid battery junction block assembly

  • Service plug grip
P3134 661 Communication error (from MG2 to MG1) Inverter with converter assembly

CAUTION / NOTICE / HINT

Tech Tips


  • If DTC P06B0-163, P06D6-511, P06E6-164, P0A1A-151, P0A1A-658, P0A1A-791, P0A1B-786, P0A1B-794, P1C2A-155, P1C2B-192, P1C73-512, P3133-659 or P3134-661 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.


    1. Turn the power switch on (IG) and wait for 5 seconds or more.

  • If DTC P1CA6-156 or P1CA7-193 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.


    1. Turn the power switch on (IG) and wait for 1 minute or more.

  • If DTC P0A1A-166 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.


    1. Turn the power switch on (READY).

    2. With the vehicle stopped and park (P) selected, depress the accelerator pedal and start the engine.

    3. Depress the accelerator pedal and keep the engine running for 30 seconds or more.

  • If DTC P0A1B-198 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.


    1. Turn the power switch on (READY).

    2. Drive the vehicle at 3 mph (5 km/h) or more for 30 seconds or more.

PROCEDURE


  1. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Check if DTCs are output.

      Result
      Result Proceed to
      DTC P0A1A-151 or P3133-659 is output. A
      Other than above. B

    5. Turn the power switch off.


    B

    REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS Click here

    A

  2. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Check if DTCs are output.

      Result
      Result Proceed to
      Only DTC P0A1A-151, P3133-659 or P324E-788 is output. A
      DTC P0A94-172, P0A94-553, P0A94-557, P0CA3-442, P3004-800 or P3004-801 is also output. B
      Other than above. C

    5. Turn the power switch off.


    B

    CLEAR DTC Click here

    C

    GO TO DTC CHART (HYBRID CONTROL SYSTEM) Click here

    A

  3. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Read and record the DTCs and freeze frame data.

    5. Clear DTCs and freeze frame data.

    6. Turn the power switch off.


    NEXT

  4. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch off and wait for 30 seconds or more.

    3. Turn the power switch on (IG) and wait for 5 seconds or more.

    4. Turn the power switch on (READY).

    5. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    6. Check if DTCs are output.

      Result
      Result Proceed to
      No DTCs are output (not including history DTCs). A
      Only DTC P0A1A-151, P3133-659 or P324E-788 is output. B
      Other than above. C

    7. Turn the power switch off.


    C

    GO TO DTC CHART (HYBRID CONTROL SYSTEM) Click here

    A

    REPLACE MG CONTROL COMPUTER Click here

    B

    REPLACE POWER MODULE INTELLIGENT TRANSISTOR KIT AND MG CONTROL COMPUTER Click here

  5. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Read and record the DTCs and freeze frame data.

    5. Clear DTCs and freeze frame data.

    6. Turn the power switch off.


    NEXT

  6. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG) and wait for 5 seconds or more.

    3. Turn the power switch on (READY) and wait for 5 seconds or more.

    4. Depress the accelerator pedal with the engine stopped and park (P) selected to start the engine and idle it for 10 seconds or more.

    5. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    6. Check if DTCs are output.

      Result
      Result Proceed to
      No DTCs are output. A
      DTCs other than P0A94-553, P0A94-557, P0CA3-442, P3004-800 or P3004-801 are output. B
      DTC P0A94-553, P0A94-557, P0CA3-442, P3004-800 or P3004-801 is output. C

    7. Turn the power switch off.


    A

    REPLACE POWER MODULE INTELLIGENT TRANSISTOR KIT Click here

    B

    REPLACE POWER MODULE INTELLIGENT TRANSISTOR KIT AND MG CONTROL COMPUTER Click here

    C

    REPLACE POWER MODULE INTELLIGENT TRANSISTOR KIT, MG CONTROL COMPUTER , HYBRID BATTERY JUNCTION BLOCK ASSEMBLY AND SERVICE PLUG GRIP Click here