FRONT DOOR LOCK INSPECTION

PROCEDURE


  1. INSPECT FRONT DOOR LOCK ASSEMBLY LH


    1. A01SB7IC01
      *a Unlock
      *b Lock
      *c

      Component without harness connected

      (Front Door Lock Assembly LH)

      Check the door lock motor operation.


      1. Apply battery voltage to the motor connector and check the operation of the door lock motor.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → Terminal 4 (L)

        Battery negative (-) → Terminal 1 (UL)

        		 Lock

        Battery positive (+) → Terminal 1 (UL)

        Battery negative (-) → Terminal 4 (L)

        		 Unlock

        If the result is not as specified, replace the front door lock assembly LH.

    2. Check the operation of the door unlock detection switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        7 (E) - 8 (LSSR) Lock 10 kΩ or higher
        Unlock Below 1 Ω

        If the result is not as specified, replace the front door lock assembly LH.

    3. A01SCOBC02
      *a Unlock
      *b Neutral
      *c Lock
      *d

      Component without harness connected

      (Front Door Lock Assembly LH)

      Check the resistance of the lock and unlock switch (for LHD).


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        9 (L) - 7 (E) Lock Below 1 Ω

        9 (L) - 7 (E)

        10 (UL) - 7 (E)

        		 Neutral 10 kΩ or higher
        10 (UL) - 7 (E) Unlock Below 1 Ω

        If the result is not as specified, replace the front door lock assembly LH.

  2. INSPECT FRONT DOOR LOCK ASSEMBLY RH


    1. A01SCZXC06
      *a Unlock
      *b Lock
      *c

      Component without harness connected

      (Front Door Lock Assembly RH)

      Check the door lock motor operation.


      1. Apply battery voltage to the motor connector and check the operation of the door lock motor.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → 4 (L)

        Battery negative (-) → 1 (UL)

        		 Lock

        Battery positive (+) → 1 (UL)

        Battery negative (-) → 4 (L)

        		 Unlock

        If the result is not as specified, replace the front door lock assembly RH.

    2. Check the operation of the door unlock detection switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        7 (LSSR) - 8 (E) Lock 10 kΩ or higher
        7 (LSSR) - 8 (E) Unlock Below 1 Ω

        If the result is not as specified, replace the front door lock assembly RH.

    3. A01SB43C12
      *a Unlock
      *b Neutral
      *c Lock
      *d

      Component without harness connected

      (Front Door Lock Assembly RH)

      Check the operation of the door key lock and unlock switch (for RHD).


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        6 (L) - 8 (E) Held to lock side Below 1 Ω

        6 (L) - 8 (E)

        5 (UL) - 8 (E)

        		 Neutral 10 kΩ or higher
        5 (UL) - 8 (E) Held to unlock side Below 1 Ω

        If the result is not as specified, replace the front door lock assembly RH.