POWER BACK DOOR SYSTEM DATA LIST / ACTIVE TEST

  1. DATA LIST

    Tip:

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Back Door, Main Body or Entry&Start* / Data List.

      • *: w/ Entry and Start System

    5. According to the display on the GTS, read the Data List.

      Body Electrical > Back Door > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      Door Lock Status

      Back door condition signal

      Lock or Unlock

      Lock: Back door locked

      Unlock: Back door unlocked

      -

      Half Latch SW

      Latch switch signal

      ON or OFF

      ON: Back door lock motor open-latched

      OFF: Back door lock motor full-latched or half-latched

      -

      Closer Position SW

      Sector switch signal

      ON or OFF

      ON: Back door lock sector gear in center position

      OFF: Back door lock sector gear out of center position

      -

      Pawl Position Switch

      Pawl switch signal

      ON or OFF

      ON: Back door lock motor open-latched

      OFF: Back door lock motor except open-latched

      Refer to "POWER BACK DOOR OPERATION TIMING CHART"*1

      Courtesy SW

      Back door courtesy switch signal

      ON or OFF

      ON: Back door open

      OFF: Back door closed

      -

      PBD Touch Sensor (Right)

      Power back door sensor assembly RH signal

      ON, OFF or Open

      ON: Power back door sensor assembly RH pressed

      OFF: Power back door sensor assembly RH not pressed

      Open: Power back door sensor assembly RH circuit open

      -

      PBD Touch Sensor (Left)

      Power back door sensor assembly LH signal

      ON, OFF or Open

      ON: Power back door sensor assembly LH pressed

      OFF: Power back door sensor assembly LH not pressed

      Open: Power back door sensor assembly LH circuit open

      -

      PBD Main SW

      Power back door ON/OFF signal

      ON or OFF

      Customize setting displayed

      -

      PBD Close SW

      Door control switch assembly signal

      ON or OFF

      ON: Door control switch assembly pushed

      OFF: Door control switch assembly not pushed

      -

      IG SW

      Ignition switch signal

      ON or OFF

      ON: Ignition switch ON

      OFF: Ignition switch off

      "OFF" is also displayed for this item when the ignition switch is ACC.

      PBD Position (3/4-Open)

      Load signal detected during back door closing operation (3/4 - Open)

      Caution or OK

      Caution: Load detected between back door 3/4 and fully open position during back door closing operation

      OK: No load detected between back door 3/4 and fully open position during back door closing operation

      -

      PBD Position (2/4-3/4)

      Load signal detected during back door closing operation (2/4 - 3/4)

      Caution or OK

      Caution: Load detected between back door 2/4 and 3/4 open position during back door closing operation

      OK: No load detected between back door 2/4 and 3/4 open position during back door closing operation

      -

      PBD Position (1/4-2/4)

      Load signal detected during back door closing operation (1/4 - 2/4)

      Caution or OK

      Caution: Load detected between back door 1/4 and 2/4 open position during back door closing operation

      OK: No load detected between back door 1/4 and 2/4 open position during back door closing operation

      -

      PBD Position (Close-1/4)

      Load signal detected during back door closing operation (Closed - 1/4)

      Caution or OK

      Caution: Load detected between back door fully closed and 1/4 open position during back door closing operation

      OK: No load detected between back door fully closed and 1/4 open position during back door closing operation

      -

      Closed Position Initialization

      Back door fully closed position memorized signal

      Not Initialized or Initialized

      Not Initialized: Back door fully closed position not memorized

      Initialized: Back door fully closed position memorized

      -

      PBD SW Operation

      Power back door switch operation

      ON or 0.8s

      Current customize setting displayed

      -

      PBD Assist Open Operation

      Function that enables or disables the power back door assist open operation. When PBD Assist Open Operate is set to ON (enabled) the back door will open automatically when the back door opener switch assembly (opener switch) is operated.

      ON or OFF

      Current customize setting displayed

      -

      PBD Assist Close Operation

      Function that enables or disables the power back door assist close operation. When PBD Assist Close Operate is set to ON (enabled), the back door will close automatically when operated in the close direction manually.

      OFF or ON

      Current customize setting displayed

      -

      Door Unlock with 1 Motion.

      Function that selects the door or doors to unlock when the back door is locked and the transmitter switch is pushed to operate the power back door.

      Back Door or ALL DOORS

      Current customize setting displayed

      -

      Wireless Power Back Door Open

      Function that operates the power back door by pushing the transmitter switch (electrical key transmitter sub-assembly).

      Lock:OFF/Unlock:OFF, Lock:OFF/Unlock:ON, Lock:OFF/Unlock:Twice, Lock:OFF/Unlock:0.8s, Lock:Twice/Unlock:Twice or Lock:0.8s/Unlock:0.8

      Current customize setting displayed

      Opening operation differs depending on the country.

      Power Back Door Opening Adjust

      Function that can be used to set the power back door opening angle at 6 different positions.

      Min, Small, Middle, Large, Max or User Setting Position

      Current customize setting displayed

      -

      Emblem Sensor

      Whether rear emblem sensor assembly is equipped or not*2

      Without or With

      Without: Rear emblem sensor assembly not equipped

      With: Rear emblem sensor assembly equipped

      Not applicable

      Emblem Sensor Detection

      Rear emblem sensor assembly detection status*2

      ON or OFF

      ON: Rear emblem sensor assembly detecting

      OFF: Rear emblem sensor assembly not detecting

      Not applicable

      PBD/Emblem Sensor Function

      PBD and rear emblem sensor assembly function setting status*2

      PBD OFF/Emblem OFF, PBD ON/Emblem OFF or PBD ON/Emblem ON

      Customized value displayed

      Not applicable

      PBD Buzzer Volume Adjust

      PBD buzzer volume setting status

      Small, Middle or Large

      Customized value displayed

      -

      PBD Buzzer Function

      PBD buzzer sounding function setting status

      OFF, Start Buzzer On/In Operation Buzzer OFF, Start Buzzer OFF/In Operation Buzzer ON or ON

      Customized value displayed

      -

      PBD Buzzer Tone

      PBD buzzer tone setting status

      Pattern A, Pattern B or Pattern C

      Customized value displayed

      -

      Kick Sensor Connection

      Status of the kick door control sensor connection*3

      Without or With

      Without: Kick door control sensor not equipped

      With: Kick door control sensor equipped

      When checking this item, disconnect the negative (-) battery terminal, wait 1 minute or more, and then reconnect the negative (-) battery terminal with the connectors of the multiplex network door ECU and kick door control sensor connected.

      Kick Sensor Detection

      Status of the kick door control sensor detection*3

      OFF or ON

      OFF: Kick door control sensor not detecting a foot

      ON: Kick door control sensor detecting a foot

      -

      Kick Sensor Error

      Status of the kick door control sensor error*3

      Normal or Error

      Normal: Kick door control sensor is normal

      Error: Kick door control sensor is abnormal

      -

      Kick Sensor Function

      Status of the touchless power back door function*3

      OFF or ON

      Customized value displayed

      -

      #Codes

      The number of DTCs

      Min.: 0

      Max.: 255

      The number of DTCs

      -

      • *1: Refer to "POWER BACK DOOR OPERATION TIMING CHART"

        Click here

      • *2: Although the item is displayed on the GTS, it is not applicable to this vehicle.

      • *3: w/ Touchless Power Back Door

      Body Electrical > Main Body > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      Back Door Open

      Back door lock

      Permit or Prohibit

      Permit: Back door unlocked

      Prohibit: Back door locked

      -

      Back Door Open SW

      Back door control switch signal

      ON or OFF

      ON: Back door control switch on

      OFF: Back door control switch off

      -

      Back Door Open Handle SW

      Back door opener switch assembly signal

      ON or OFF

      ON: Back door opener switch assembly on

      OFF: Back door opener switch assembly off

      -

      Body Electrical > Entry&Start > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      Tr/B-Door Unlock SW

      Back door opener switch assembly signal

      ON or OFF

      ON: Back door opener switch assembly on

      OFF: Back door opener switch assembly off

      -

  2. ACTIVE TEST

    Tip:

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Back Door / Active Test.

    5. According to the display on GTS perform the "Active Test".

      Body Electrical > Back Door > Active Test

      Tester Display

      Measurement Item

      Control Range

      Diagnostic Note

      Latch Release

      Latch release operation

      ON or OFF

      -

      PBD Open/Close

      Power back door motor operation

      Forward, Reverse or OFF

      -

      PBD Buzzer

      Power back door warning buzzer sound

      ON or OFF

      -