СИСТЕМА SFI, Diagnostic DTC:P060A

DTC Code DTC Name
P060A Internal Control Module Monitoring Processor Performance

DESCRIPTION

The main CPU and sub CPU of the ECM perform data communication between each other. The main CPU monitors the communications and WDC pulses from the sub CPU. When the signal malfunctions below are detected, a DTC is stored.

DTC No. DTC Detection Condition Trouble Area
P060A

A CPU reset is performed after one of the following conditions is met (1 trip detection logic):


  • There is an ECM main CPU error.

  • There is an ECM sub CPU error.

  • There is an electronic throttle monitoring CPU error.

ECM

MONITOR STRATEGY

Required sensors/Components ECM
Frequency of operation Once per driving cycle

CONFIRMATION DRIVING PATTERN


  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON and turn the intelligent tester on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

  4. Turn the intelligent tester off.

  5. Turn the ignition switch off.

  6. Disconnect the intelligent tester.

  7. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

  8. Connect the cable to the negative (-) battery terminal.

  9. Connect the intelligent tester to the DLC3.

  10. Turn the ignition switch to ON and turn the intelligent tester on.

  11. Wait 16 seconds or more.

  12. Enter the following menus: Powertrain / Engine and ECT / DTC.

  13. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  14. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  15. Input the DTC: P060A.

  16. Check the DTC judgment result.

    Tester Display Description
    NORMAL
    • DTC judgment completed

    • System normal

    ABNORMAL
    • DTC judgment completed

    • System abnormal

    INCOMPLETE
    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions

    N/A
    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

  17. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs Click here.

    Tech Tips


    • If a permanent DTC is output, the system is malfunctioning.

    • If no permanent DTC is output, the system is normal.

INSPECTION PROCEDURE

Note

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

Tech Tips

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK FOR DTC


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Clear the DTCs Click here.

    5. Turn the intelligent tester off.

    6. Turn the ignition switch off.

    7. Disconnect the intelligent tester.

    8. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

    9. Connect the cable to the negative (-) battery terminal.

    10. Connect the intelligent tester to the DLC3.

    11. Turn the ignition switch to ON and turn the intelligent tester on.

    12. Wait 16 seconds or more.

    13. Enter the following menus: Powertrain / Engine and ECT / DTC.

    14. Check for DTCs.

      OK
      P060A is not output.

    NG
    OK