AIRBAG SYSTEM, Diagnostic DTC:B1610/13

DTC Code DTC Name
B1610/13 Front Airbag Sensor RH Circuit Malfunction

SYSTEM DESCRIPTION

The front airbag sensor RH consists of a diagnostic circuit and frontal deceleration sensor, etc. If the center airbag sensor receives signals from the frontal deceleration sensor, it determines whether the SRS should be activated.

DTC B1610/13 is stored when a malfunction is detected in the front airbag sensor RH circuit.

DTC Code DTC Detection Condition Trouble Area
B1610/13

One of the following conditions is met:


  • A front airbag sensor RH malfunction.

  • A center airbag sensor malfunction.

  • Front airbag sensor RH

  • Engine room main wire

  • Instrument panel wire

  • Center airbag sensor assembly

WIRING DIAGRAM

A004P9CE14
*a Front Airbag Sensor RH
*b Center Airbag Sensor

CAUTION / NOTICE / HINT

Note


  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  • When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected Click here.

PROCEDURE


  1. CHECK CONNECTION OF CONNECTORS


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the center airbag sensor and front airbag sensor RH.

      OK
      The connectors are properly connected.

    NG

    CONNECT CONNECTORS PROPERLY

    OK

  2. CHECK CONNECTORS


    1. Disconnect the connectors from the center airbag sensor and front airbag sensor RH.

    2. Check that the connectors (on the center airbag sensor side and front airbag sensor RH side) are not damaged.

      OK
      The connectors are not deformed or damaged.

    NG

    REPLACE HARNESS AND CONNECTOR

    OK

  3. CHECK FRONT AIRBAG SENSOR RH CIRCUIT

    A004TVXE01
    Text in Illustration
    *1 Front Airbag Sensor RH
    *2 Center Airbag Sensor
    *3 Connector E
    *4 Connector B
    *5 Service Wire
    *a

    Front view of wire harness connector

    (to Front Airbag Sensor RH)
    *b

    Rear view of wire harness connector

    (to Center Airbag Sensor)

    1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      A17-2 (+SR) - Body ground Ignition switch ON Below 1 V
      A17-1 (-SR) - Body ground Ignition switch ON Below 1 V

    3. Turn the ignition switch off.

    4. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    5. Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A17-2 (+SR) - A17-1 (-SR) Always Below 1 Ω

    7. Disconnect the service wire from connector B.

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A17-2 (+SR) - A17-1 (-SR) Always 1 MΩ or higher
      A17-2 (+SR) - Body ground Always 1 MΩ or higher
      A17-1 (-SR) - Body ground Always 1 MΩ or higher

    NG

    CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - ENGINE ROOM MAIN WIRE) Click here

    OK

  4. CHECK FRONT AIRBAG SENSOR RH

    A004TNNE01
    Text in Illustration
    *1 Front Airbag Sensor LH
    *2 Center Airbag Sensor

    1. Connect the connector to the center airbag sensor.

    2. Interchange the front airbag sensor LH with RH and connect the connectors to them.

    3. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    4. Turn the ignition switch to ON, and wait for at least 60 seconds.

    5. Clear the DTCs stored in the memory Click here.

    6. Turn the ignition switch off.

    7. Turn the ignition switch to ON, and wait for at least 60 seconds.

    8. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1610 and B1615 are not output A
      DTC B1615 is output B
      DTC B1610 is output C

      Tech Tips

      Codes other than DTC B1610 and B1615 may be output at this time, but they are not related to this check.


    A

    USE SIMULATION METHOD TO CHECK Click here

    B

    REPLACE FRONT AIRBAG SENSOR RH Click here

    C

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here

  5. CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - ENGINE ROOM MAIN WIRE)

    A004O6FE02
    Text in Illustration
    *1 Front Airbag Sensor RH
    *2 Engine Room Main Wire
    *3 Instrument Panel Wire
    *4 Center Airbag Sensor
    *5 Connector C
    *6 Connector B
    *7 Service Wire
    *a

    Front view of wire harness connector

    (to Engine Room Main Wire)
    *b

    Rear view of wire harness connector

    (to Center Airbag Sensor)

    1. Disconnect the instrument panel wire connector from the engine room main wire.

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      AD8-2 (+SR) - Body ground Ignition switch ON Below 1 V
      AD8-1 (-SR) - Body ground Ignition switch ON Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    6. Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      AD8-2 (+SR) - AD8-1 (-SR) Always Below 1 Ω

    8. Disconnect the service wire from connector B.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      AD8-2 (+SR) - AD8-1 (-SR) Always 1 MΩ or higher
      AD8-2 (+SR) - Body ground Always 1 MΩ or higher
      AD8-1 (-SR) - Body ground Always 1 MΩ or higher

    OK

    REPLACE ENGINE ROOM MAIN WIRE

    NG

    REPLACE INSTRUMENT PANEL WIRE