STEERING COLUMN ASSEMBLY INSTALLATION

PROCEDURE

  1. INSPECT STEERING COLUMN ASSEMBLY

    Click here

  2. INSTALL STEERING COLUMN ASSEMBLY

    1. Install the steering column assembly with the bolt and 2 nuts.

      Bolt

      36 N*m

      367 kgf*cm

      27 ft.*lbf

      Nut

      25 N*m

      255 kgf*cm

      18 ft.*lbf

      Note:

      Make sure that the wire harness is not interfering with the steering column assembly.

    2. Connect each connector and engage each wire harness clamp to the steering column assembly.

    3. C272220

      Engage the 2 wire harness clamps.

    4. Connect the 2 connectors.

  3. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

  4. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

  5. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

    1. w/ Instrument Panel Under Cover:

  6. INSTALL NO. 1 SWITCH HOLE BASE (w/o Driver Side Knee Airbag)

  7. INSTALL LOWER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Driver Side Knee Airbag)

  8. INSTALL UPPER INSTRUMENT PANEL ASSEMBLY

  9. INSTALL BRAKE PEDAL SUPPORT ASSEMBLY

  10. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

    1. C274653C01

      *a

      Matchmark

      Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.

    2. Install the No. 2 steering intermediate shaft assembly to the steering column assembly.

    3. Install the bolt.

      35 N*m

      357 kgf*cm

      26 ft.*lbf

  11. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

    1. C272218C01

      *a

      Matchmark

      Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering intermediate shaft assembly.

    2. Connect the No. 2 steering intermediate shaft assembly to the steering intermediate shaft assembly.

    3. Install the bolt.

      35 N*m

      357 kgf*cm

      26 ft.*lbf

  12. INSTALL COLUMN HOLE COVER SILENCER SHEET

    1. Install the column hole cover silencer sheet with the 2 clips.

    2. Install the floor carpet.

  13. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

    Note:

    w/ VSC:

    • Do not replace the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.

    • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel with the battery connected and the ignition switch ON.

    • Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.

    1. Using pliers, expand the clamp.

    2. While holding the clamp expanded, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and engage the claw.

    3. Return the clamp to its original position.

    4. Connect each connector to the turn signal switch assembly with spiral cable sub-assembly.

  14. INSTALL STEERING COLUMN COVER

    1. Engage the 2 claws to install the steering column cover (upper).

    2. Engage the 5 claws to install the steering column cover (lower).

    3. Install the 2 screws.

  15. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  16. INSPECT AND ADJUST SPIRAL CABLE SUB-ASSEMBLY (w/o VSC)

    Click hereClick here

  17. INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (w/ VSC)

    Click hereClick here

  18. INSTALL STEERING WHEEL ASSEMBLY

    Click here

  19. INSTALL HORN BUTTON ASSEMBLY

    Click here

  20. PERFORM CALIBRATION OF TORQUE SENSOR ZERO POINT

    Click here

  21. ADJUST PARKING ASSIST SYSTEM (w/ Parking Assist Monitor System)

    Click here