FRONT BUMPER REASSEMBLY

PROCEDURE


  1. INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY LH


    1. B005ZDD

      Engage the guide.

    2. Install the front side member bracket sub-assembly LH with the 4 bolts.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

  2. INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  3. INSTALL FRONT BUMPER SIDE SUPPORT LH


    1. B005Y8FE03
      Text in Illustration
      *a Bolt
      *b Screw

      Engage the 2 claws.

    2. Install the front bumper side support LH with the bolt and screw.

      Torque:
      Bolt
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }
      Screw
      2.0 N*m  { 20 kgf*cm, 18 in.*lbf }

  4. INSTALL FRONT BUMPER SIDE SUPPORT RH

    Tech Tips

    Use the same procedure as for the LH side.

  5. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY


    1. B005YOT

      Engage the claw.

    2. Install the front bumper reinforcement sub-assembly with the 6 bolts.

      Torque:
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }

    3. Engage the 3 clamps.

  6. INSTALL FRONT BUMPER ENERGY ABSORBER


    1. B005Y19

      Engage the 2 guides to install the front bumper energy absorber.

  7. INSTALL FRONT BUMPER EXTENSION LH


    1. B005Z1X

      Engage the 2 claws to install the front bumper extension LH.

  8. INSTALL FRONT BUMPER EXTENSION RH

    Tech Tips

    Use the same procedure as for the LH side.

  9. INSTALL FRONT FENDER LINER RETAINER


    1. B005Z4F

      Engage the claw to install the 3 front fender liner retainers.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  10. INSTALL AIR INTAKE DUCT LH


    1. B005XZ2

      Install the 2 screws.

    2. B005Y08E02
      Text in Illustration
      *1 Pin Hold Clip
      *a Correct
      *b Incorrect

      Install the air intake duct LH with the 3 pin hold clips as shown in the illustration.

      Note

      Insert the pin hold clip with the slot aligned vertically. Do not rotate the clip after inserting it. After installation, confirm that the slot is aligned vertically.

  11. INSTALL AIR INTAKE DUCT RH

    Tech Tips

    Use the same procedure for the RH side and LH side.

  12. INSTALL FRONT BUMPER HOLE COVER LH


    1. B005XM8E02
      Text in Illustration
      *a Hook

      Engage the hook.

    2. Engage the 2 claws and install the front bumper hole cover LH.

  13. INSTALL FRONT BUMPER HOLE COVER RH

    Tech Tips

    Use the same procedure as for the LH side.

  14. INSTALL LOWER RADIATOR GRILLE SUB-ASSEMBLY


    1. Engage the 4 guides and 14 claws.

      B005YE1
    2. B005XNN

      Install the 4 outside moulding retainers.

    3. B005YLA

      Install the lower radiator grille sub-assembly with the 2 screws.

  15. INSTALL LOWER NO. 2 RADIATOR GRILLE


    1. B005ZOW

      Engage the 6 claws.

    2. B005XNC

      Install the lower No. 2 radiator grille with the 2 screws.

  16. INSTALL RADIATOR GRILLE


    1. Engage the guide and 16 claws.

      B005XZD
    2. B005YY1

      Install the 4 clips.

    3. Install the radiator grille with the 2 screws.

  17. INSTALL FRONT BUMPER EMBLEM SUB-ASSEMBLY


    1. A005AH8

      Engage the 2 pins and 4 claws.

    2. A005ADD

      Install the front bumper emblem sub-assembly with the 2 screws.

  18. INSTALL HOOD TO FRONT END PANEL SEAL


    1. Clean the front bumper cover.


      1. Remove any remaining double-sided tape from the front bumper cover.

      2. Wipe off any tape adhesive residue with cleaner.

    2. Remove the release paper from a new hood to front end panel seal.

      Tech Tips

      After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. B005YPI

      Install the hood to front end panel seal with 2 clips.

      Text in Illustration
      B005XMV Double-sided Tape

  19. INSTALL FOG LIGHT ASSEMBLY LH

    Click here

  20. INSTALL FOG LIGHT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  21. INSTALL NO. 3 ENGINE ROOM WIRE


    1. B005ZO1

      Engage the 11 clamps to install the No. 3 engine room wire.

  22. INSTALL DAYTIME RUNNING LIGHT ASSEMBLY LH

    Click here

  23. INSTALL DAYTIME RUNNING LIGHT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  24. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ Intelligent Parking Assist System)

    Click here

  25. INSTALL NO. 1 ULTRASONIC SENSOR (w/ Intelligent Parking Assist System)

    Click here