СИСТЕМА SFI, Diagnostic DTC:P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135

DTC Code	DTC Name
P0120	Throttle / Pedal Position Sensor / Switch "A" Circuit
P0121	Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem
P0122	Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input
P0123	Throttle / Pedal Position Sensor / Switch "A" Circuit High Input
P0220	Throttle / Pedal Position Sensor / Switch "B" Circuit
P0222	Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input
P0223	Throttle / Pedal Position Sensor / Switch "B" Circuit High Input
P2135	Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation

DESCRIPTION

Tech Tips

This Electronic Throttle Control System (ETCS) does not use a throttle cable.
This throttle position sensor is a non-contact type.

The throttle position sensor is mounted on the throttle body and it detects the opening angle of the throttle valve. This sensor is electronically controlled and uses Hall-effect elements so that accurate control and reliability can be obtained. The throttle position sensor has 2 sensor elements / signal outputs: VTA1 and VTA2. VTA1 is used to detect the throttle opening angle and VTA2 is used to detect a malfunction in VTA1. Voltage applied to VTA1 and VTA2 changes between 0 to 5 V in proportion to the opening angle of the throttle valve. The ECM performs several checks to confirm proper operation of the throttle position sensor and VTA1.

The ECM judges the actual opening angle of the throttle valve using signals input from terminals VTA1 and VTA2. Then the ECM controls the throttle motor, which controls the throttle valve angle properly in response to operation of the accelerator pedal.

DTC No.	DTC Detection Condition	Trouble Area
P0120	Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds (1 trip detection logic)	Throttle position sensor (built into throttle body) ECM
P0121	Difference between VTA1 and VTA2 voltages is less than 0.8 V, or more than 1.6 V for 2 seconds. (1 trip detection logic)	Throttle position sensor (built into throttle body) Throttle position sensor circuit ECM
P0122	Output voltage of VTA1 0.2 V or less for 2 seconds (1 trip detection logic)	Throttle position sensor (built into throttle body) Short in VTA1 circuit Open in VC circuit ECM
P0123	Output voltage of VTA1 4.8 V or more for 2 seconds (1 trip detection logic)	Throttle position sensor (built into throttle body) Open in VTA1 circuit Open in E2 circuit Short between VC and VTA1 circuits ECM
P0220	Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds (1 trip detection logic)	Throttle position sensor (built into throttle body) ECM
P0222	Output voltage of VTA2 0.5 V or less for 2 seconds (1 trip detection logic)	Throttle position sensor (built into throttle body) Short in VTA2 circuit Open in VC circuit ECM
P0223	Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 1.8 V for 2 seconds (1 trip detection logic)	Throttle position sensor (built into throttle body) Open in VTA2 circuit Open in E2 circuit Short between VC and VTA2 circuits ECM
P2135	Either condition (a) or (b) met (1 trip detection logic): (a) Difference between output voltages of VTA1 and VTA2 0.02 V or less for 0.5 seconds or more (b) Output voltage of VTA1 0.2 V or less, and VTA2 0.5 V or less, for 0.4 seconds or more	Short between VTA1 and VTA2 circuits Throttle position sensor (built into throttle body) ECM

DTC No.

DTC Detection Condition

Trouble Area

P0120

Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds

(1 trip detection logic)

Throttle position sensor (built into throttle body)

P0121

Difference between VTA1 and VTA2 voltages is less than 0.8 V, or more than 1.6 V for 2 seconds.

(1 trip detection logic)

Throttle position sensor (built into throttle body)
Throttle position sensor circuit
ECM

P0122

Output voltage of VTA1 0.2 V or less for 2 seconds

(1 trip detection logic)

Throttle position sensor (built into throttle body)

Short in VTA1 circuit

Open in VC circuit

P0123

Output voltage of VTA1 4.8 V or more for 2 seconds

(1 trip detection logic)

Throttle position sensor (built into throttle body)

Open in VTA1 circuit

Open in E2 circuit

Short between VC and VTA1 circuits

P0220

Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds

(1 trip detection logic)

Throttle position sensor (built into throttle body)

P0222

Output voltage of VTA2 0.5 V or less for 2 seconds

(1 trip detection logic)

Throttle position sensor (built into throttle body)

Short in VTA2 circuit

Open in VC circuit

P0223

Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 1.8 V for 2 seconds (1 trip detection logic)

Throttle position sensor (built into throttle body)

Open in VTA2 circuit

Open in E2 circuit

Short between VC and VTA2 circuits

P2135

Either condition (a) or (b) met (1 trip detection logic):

(a) Difference between output voltages of VTA1 and VTA2 0.02 V or less for 0.5 seconds or more

(b) Output voltage of VTA1 0.2 V or less, and VTA2 0.5 V or less, for 0.4 seconds or more

Short between VTA1 and VTA2 circuits

Throttle position sensor (built into throttle body)

Note

When a malfunction is detected, the throttle valve is locked at a certain opening angle. Also, all electronically controlled throttle operations are canceled until the system returns to normal and the ignition switch is turned OFF.

Tech Tips

When any of these DTCs is detected, check the throttle valve opening angle (Throttle Sensor Volt % and Throttle Position No. 2) using the intelligent tester.
The Throttle Sensor Volt % is the VTA1 signal (expressed as a percentage), and Throttle Position No. 2 is the VTA2 signal (expressed as a voltage).

Reference (Normal condition):
Tester Display	Accelerator Pedal Fully Released	Accelerator Pedal Fully Depressed
Throttle Sensor Volt %	10 to 22%	64 to 96%
Throttle Position No. 2	2.1 to 3.1 V	4.6 to 5.5 V

MONITOR DESCRIPTION

The ECM uses the throttle position sensor to monitor the throttle valve opening angle. There are several checks that the ECM performs to confirm that the throttle position sensor is operating properly.

P0120, P0122, P0123, P0220, P0222, P0223 and P2135

A specific voltage difference is expected between the sensor terminals, VTA1 and VTA2, for each throttle valve opening angle. If the difference between VTA1 and VTA2 is incorrect, the ECM interprets this as a malfunction in the sensor and stores a DTC.
VTA1 and VTA2 each have a specific voltage range. If VTA1 or VTA2 is outside the normal operating range, the ECM interprets this as a malfunction in the sensor and stores a DTC.
VTA1 and VTA2 should never be close to the same voltage level. If VTA1 is within 0.02 V of VTA2, the ECM determines that there is a short circuit in the sensor and stores a DTC.

If the malfunction is not repaired successfully, a DTC is stored 10 seconds after the engine is next started.

P0121

This sensor transmits two signals: VTA1 and VTA2. VTA1 is used to detect the throttle opening angle and VTA2 is used to detect malfunctions in VTA1. The ECM performs several checks to confirm that the throttle position sensor and VTA1 are operating properly.

For each throttle opening angle, a specific voltage difference is expected between the outputs of VTA1 and VTA2. If the output voltage difference between the two signals deviates from the normal operating range, the ECM interprets this as a malfunction of the throttle position sensor. The ECM illuminates the MIL and stores the DTC.

If the malfunction is not repaired successfully, the DTC is stored 2 seconds after the engine is next started.

FAIL-SAFE

If the ETCS is malfunctioning, the ECM cuts off the current to the throttle actuator. The throttle control valve returns to a predetermined throttle position (approximately 6°) by the force of the return spring.

Then, required engine power is calculated by using the ignition timing and accelerator pedal position. The engine is controlled by intermittent fuel-cut.

If the accelerator pedal is depressed firmly and slowly, the vehicle can be driven at minimum speed. If the accelerator pedal is depressed quickly, the vehicle may speed up and slow down erratically.

WIRING DIAGRAM

INSPECTION PROCEDURE

Tech Tips

If DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
These DTCs are related to the throttle position sensor.

PROCEDURE

READ DATA LIST (THROTTLE POSITION, THROTTLE POSITION NO. 2)

Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Sensor Volt % and Throttle Position No. 2.

Read the values.

Result

TP (VTA1) When AP Released	TP No. 2 (VTA2) When AP Released	TP (VTA1) When AP Depressed	TP No. 2 (VTA2) When AP Depressed	Suspected Area	Proceed to
0%	0 to 0.2 V	0%	0 to 0.2 V	VC circuit open	A
100%	4.6 to 5.0 V	100%	4.6 to 5.0 V	E2 circuit open	A
0 or 100%	2.1 to 3.1 V (fail-safe)	0 or 100%	2.1 to 3.1 V (fail-safe)	VTA1 circuit open or ground short	A
10 to 22% (fail-safe)	0 to 0.2 V, or 4.6 to 5.0 V	10 to 22% (fail-safe)	0 to 0.2 V, or 4.6 to 5.0 V	VTA2 circuit open or ground short	A
10 to 22%	2.1 to 3.1 V	64 to 96% (not fail-safe)	4.6 to 5.0 V (not fail-safe)	Throttle position sensor circuit is normal	B

Tech Tips

If DTC P0121 is output, proceed to "Check Wire Harness (Throttle Position Sensor - ECM)".
TP stands for throttle position, and AP stands for accelerator pedal.
VTA1 is expressed as a percentage, and VTA2 is expressed as a voltage.

CHECK IF DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS) Click here

CHECK WIRE HARNESS (THROTTLE POSITION SENSOR - ECM)

Disconnect the T25 throttle body connector.
Disconnect the E15 ECM connector.

Measure the resistance of the wire harness side connectors.

Standard resistance

Tester Connection	Specified Condition
T25-5 (VC) - E15-23 (VC)	Below 1 Ω
T25-6 (VTA) - E15-20 (VTA1)	Below 1 Ω
T25-4 (VTA2) - E15-19 (VTA2)	Below 1 Ω
T25-3 (E2) - E15-28 (E2)	Below 1 Ω
T25-5 (VC) or E15-23 (VC) -Body ground	10 kΩ or higher
T25-6 (VTA) or E15-20 (VTA1) - Body ground	10 kΩ or higher
T25-4 (VTA2) or E15-19 (VTA2) - Body ground	10 kΩ or higher

REPAIR OR REPLACE HARNESS AND CONNECTOR

INSPECT ECM (VC VOLTAGE)

Disconnect the throttle body connector.
Turn the ignition switch ON.

Measure the voltage of the ECM connector.

Standard voltage

Tester Connection	Specified Condition
E15-23 (VC) - E15-28 (E2)	4.5 to 5.0 V

REPLACE ECM

REPLACE THROTTLE BODY

NEXT

CHECK IF DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)

Clear the DTCs Click here.
Start the engine.
Idle engine for 15 seconds or more.
Connect the intelligent tester to the DLC3.
Turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / DTC.

Read the DTCs.

Result

Display (DTC output)	Proceed to
P0120, P0121, P0122, P0123, P0220, P0222, P0223 and/or P2135	A
No output	B

SYSTEM OK

REPLACE ECM