POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM FREEZE FRAME DATA
FREEZE FRAME DATA
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and check the freeze frame data by following the prompts on the intelligent tester screen.
Table 1. Tilt & Telescopic Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
The Number of DTCs
Number of stored diagnostic trouble codes/min.: 0, max.: 255
Actual number of stored diagnostic trouble codes
-
Body Electrical > Tilt&Telescopic
Tester Display
Measurement Item
Range
Normal Condition
Diagnostic Note
Tilt Position
Current tilt position data
Min.: 0, Max.: 65535
28672 to 36864
-
Telesco Position
Current telescopic position data
Min.: 0, Max.: 65535
28672 to 36864
-
Tilt Return Position
Memorized tilt return position data
Min.: 0, Max.: 65535
28672 to 36864
-
Telesco Return Position
Memorized telescopic return position data
Min.: 0, Max.: 65535
28672 to 36864
-
Tilt Up Switch
Input state of tilt up by manual switch
ON or OFF
ON: Tilt up activated by manual switch
OFF: Tilt up not activated by manual switch
-
Tilt Up SW(CAN)
Input state of tilt up by manual switch
ON or OFF
ON: Tilt up activated by manual switch
OFF: Tilt up not activated by manual switch
-
Tilt Down Switch
Input state of tilt down by manual switch
ON or OFF
ON: Tilt down activated by manual switch
OFF: Tilt down not activated by manual switch
-
Tilt Down SW(CAN)
Input state of tilt down by manual switch
ON or OFF
ON: Tilt down activated by manual switch
OFF: Tilt down not activated by manual switch
-
Telesco Short Switch
Input state of telescopic short by manual switch
ON or OFF
ON: Telescopic short activated by manual switch
OFF: Telescopic short not activated by manual switch
-
Telesco Short SW(CAN)
Input state of telescopic short by manual switch
ON or OFF
ON: Telescopic short activated by manual switch
OFF: Telescopic short not activated by manual switch
-
Telesco Long Switch
Input state of telescopic long by manual switch
ON or OFF
ON: Telescopic long activated by manual switch
OFF: Telescopic long not activated by manual switch
-
Telesco Long SW(CAN)
Input state of telescopic long by manual switch
ON or OFF
ON: Telescopic long activated by manual switch
OFF: Telescopic long not activated by manual switch
-
T&T Manual SW Data
Voltage data of manual switch
Min.: 0.00 V, Max.: 4.99 V
Neutral position: Below 0.2 V
Tilt up: 1.67 to 2.13 V
Tilt down: 0.54 to 0.74 V
Telescopic contract: 1.08 to 1.40 V
Telescopic extend: 2.22 to 2.77 V
-
Power Source Voltage
Voltage data of power supply
Min.: 0.00 V, Max.: 19.99 V
11 to 14 V
-
Freeze Speed Info
Vehicle speed data
Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
Actual vehicle speed
-
IG Switch (CAN)
Communication state of engine switch
ON or OFF
ON: Communication normal
OFF: Communication interrupted
-
IG Switch
Input state of engine switch
ON or OFF
ON: Input signal normal
OFF: Input signal interrupted
-
Receive from Meter
Communication state of combination meter signal
OK or Interpt
OK: Communication normal
Interpt: Communication interrupted
-
Receive from Seat ECU
Communication state of position control ECU signal
OK or Interpt
OK: Communication normal
Interpt: Communication interrupted
-
Receive from Combi
Communication state of combination switch ECU signal
OK or Interpt
OK: Communication normal
Interpt: Communication interrupted
-
J/B
Communication state of main body ECU signal
OK or Interpt
OK: Communication normal
Interpt: Communication interrupted
-
Handle Position
Steering wheel position signal
Away or Return
Away: Steering wheel in away position
Return: Steering wheel in return position
(Except remote start)
-