SLIDE DOOR (w/ Power Slide Door) REASSEMBLY


  1. INSTALL SLIDE DOOR LOWER ROLLER ASSEMBLY LH


    1. Install the slide door lower roller with the 4 bolts.

      Torque:
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

  2. INSTALL SLIDE DOOR CENTER HINGE ASSEMBLY LH


    1. Install the slide door roller center hinge with the 2 bolts.

      Torque:
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

  3. INSTALL SLIDE DOOR ROLLER ASSEMBLY LH


    1. Install the slide door roller with the 2 bolts

      Torque:
      12 N*m  { 122 kgf*cm, 8.9 ft.*lbf }

  4. INSTALL SLIDE DOOR SUB-ASSEMBLY LH


    1. Fit the slide door hinge center base of the slide door back into the slide rail center from the rear of the vehicle.

    2. Insert the slide door roller upper base of the slide door into the cut area in the slide door rail upper.

    3. Fit the slide door rail lower base of the slide door through the cut area in the slide door rail lower.

  5. INSTALL SLIDE DOOR UPPER RAIL CUSHION LH

    B007PYG

    1. Install the slide door upper rail cushion with the bolt.

  6. INSTALL SLIDE RAIL END MOULDING LH

    B007WC6

    1. Engage the clip and install the slide rail end moulding.

  7. INSTALL POWER SLIDE DOOR MOTOR ASSEMBLY


    1. B007TDX

      Install the power slide door motor with the 10 bolts.

      Torque:
      7.8 N*m  { 80 kgf*cm, 69 in.*lbf }
    2. B007SVF

      Install the 2 grommets.

    3. Install the slide door lower roller assembly LH onto the belt bracket of the power slide door motor assembly.

    4. B007OT4

      Install the slide door lower rail plate with the bolt.

      Torque:
      8.3 N*m  { 85 kgf*cm, 73 in.*lbf }
    5. B007T2O

      Tighten the slide door lower roller assembly LH and belt bracket with the 2 bolts.

      Torque:
      7.8 N*m  { 80 kgf*cm, 69 in.*lbf }

  8. INSTALL SLIDE DOOR WIRE

    B007RNN

    1. Engage the clamps and install the slide door wire.

    2. Tighten the bolt.

  9. INSTALL SLIDE DOOR LOCK REMOTE CONTROL ASSEMBLY LH


    1. B007OZG

      Install the slide door lock remote control with the 5 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  10. INSTALL SLIDE DOOR LOCK RELEASE MOTOR

    B007PBF

    1. Install the slide door lock release motor with the 3 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    2. Connect the link.

    3. Connect the connector.

  11. INSTALL POWER SLIDE DOOR LOCK ASSEMBLY LH


    1. B007SPK

      Using "TORX" socket wrench T30, install the power slide door lock with the 3 screws.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    2. Tighten the bolt.

    3. Engage the clamps and connect the connector.

  12. INSTALL DOOR OPENING RELAY

    B007TTK

    1. Install the door opening relay with the bolt.

    2. Connect the connector.

  13. INSTALL SLIDE DOOR FULL OPEN STOP LOCK ASSEMBLY LH


    1. B007PTS

      Install the slide door full open stop lock with the 2 bolts.

    2. Engage the clamp.

  14. INSTALL SLIDE DOOR DOWN FEMALE STOPPER


    1. B007SM1

      Install the slide door down female stop with the bolt.

  15. INSTALL POWER SLIDE DOOR TOUCH SENSOR

    B007SIE

    1. Engage the 2 clips and install the power slide door touch sensor.

    2. Tighten the 3 bolts.

    3. Using "TORX" socket wrench T25, tighten the 6 screws.

    4. Connect the connector.

  16. INSTALL SLIDE DOOR FRONT LOCK ASSEMBLY LH


    1. B007P9L

      Using "TORX" socket wrench T30, install the slide door front lock with the 3 screws.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    2. Clamp the cable and install the end of the cable to the slide door lock remote control.

  17. INSTALL REAR DOOR LOCK CHILD PROTECTION COVER LH


    1. for Cover Type:


      1. B007VE0

        Install the rear door lock child protection cover with the clip.

    2. for Tape Type:

      Tech Tips

      When installing the front door weatherstrip, heat the vehicle body using a heat light.

      Note

      Do not heat the vehicle body excessively.


      1. Using a heat light, heat the vehicle body.

        Heating Temperature
        Item Temperature
        Vehicle Body 40 to 60°C (104 to 140°F)

      2. Remove the double-sided tape from the vehicle body.

      3. Wipe off any tape adhesive residue with cleaner.

      4. B007QGE

        Install a new rear door lock child protection cover.

  18. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH


    1. B007UF3

      Install the rear door outside handle with the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    2. Connect the 2 links.

  19. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH

    B007UJQ

    1. Install the rear door inside handle with the 2 bolts.

    2. Connect the links.

  20. INSTALL SLIDE DOOR SERVICE HOLE COVER LH

    B007P1K

    1. Apply butyl tape to the door panel, then install a new slide door service hole cover as shown in the illustration.

      Tech Tips


      • When installing the service hole cover, pull the links and connectors out through the service hole.

      • There should be no wrinkles or folds after attaching the service hole cover.

      • After attaching the service hole cover, check the quality of the seal.

    2. Connect the cable to the slide door lock remote control.

    3. Engage the clamp.

  21. INSTALL REAR NO. 2 DOOR WIRE


    1. B007SVI

      Engage the 4 clips and install the rear No. 2 door wire.

      Note

      Engage the clips by directly pushing them in by hand, not by tapping on the case surface.

    2. Tighten the 4 bolts.

      Note

      Do not tighten the bolts with any wire harness or cable wedged under the case as it may cause the case to deform or malfunction.

    3. B007UJ9

      Make sure that the wire harness is not twisted, and tighten the bolts after the clamp is fully secured by turning it in the direction indicated by the arrow mark.

    4. Connect the connector.

  22. INSTALL DOOR CONTROL RELAY ASSEMBLY

    B007PEY

    1. Install the door control relay with the bolt.

    2. Connect the connectors.

  23. INSTALL SIDE STEP REAR SUPPORT LH

    B007S5A

    1. Install the side step rear support with the 3 bolts.

      Torque:
      7.8 N*m  { 80 kgf*cm, 69 in.*lbf }

  24. INSTALL REAR DOOR SCUFF PLATE LH


    1. B007R3Z

      Connect the connector.

    2. Engage the claw and 12 clips and install the rear door scuff plate.

  25. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. B007S92

      Engage the claw and 19 clips, and install the rear door trim board.

    2. B007T23

      Using "TORX" socket wrench T25, tighten the 2 screws.

  26. INSTALL SLIDE DOOR WINDOW GARNISH LH


    1. B007VXE

      Engage the 4 clips and install the slide door window garnish.

  27. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Torque:
    5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  28. INSPECT AND ADJUST SLIDE DOOR

    Click here