NAVIGATION SYSTEM(for Navigation Receiver Type), Diagnostic DTC:B1324

DTC Code DTC Name
B1324 Lost Communication with Meter

DESCRIPTION

This DTC is stored when a communication error occurs between the navigation receiver assembly and combination meter sub-assembly.

DTC No. DTC Detection Condition Trouble Area
B1324 After the navigation receiver assembly receives a registration information signal, which is sent by the combination meter sub-assembly when the power switch is on (ACC), 1 or more times, the navigation receiver assembly cannot receive the signal for 30 seconds or more.

  • Combination meter sub-assembly

  • Navigation receiver assembly

  • Harness or connector

WIRING DIAGRAM

A005BUJE06

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER SUB-ASSEMBLY)


    1. Disconnect the L172 navigation receiver assembly connector (w/o Intelligent Parking Assist System).

    2. Disconnect the L173 navigation receiver assembly connector (w/ Intelligent Parking Assist System).

    3. Disconnect the L27 combination meter sub-assembly connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      w/o Intelligent Parking Assist System
      Tester Connection Condition Specified Condition
      L172-3 (CNH1) - L27-28 (MSCH) Always Below 1 Ω
      L172-4 (CNL1) - L27-29 (MSCL) Always Below 1 Ω
      L172-3 (CNH1) - Body ground Always 10 kΩ or higher
      L172-4 (CNL1) - Body ground Always 10 kΩ or higher
      L172-3 (CNH1) - L152-4 (CNL1) Always 10 kΩ or higher
      w/ Intelligent Parking Assist System
      Tester Connection Condition Specified Condition
      L173-3 (CNH1) - L27-28 (MSCH) Always Below 1 Ω
      L173-4 (CNL1) - L27-29 (MSCL) Always Below 1 Ω
      L173-3 (CNH1) - Body ground Always 10 kΩ or higher
      L173-4 (CNL1) - Body ground Always 10 kΩ or higher
      L173-3 (CNH1) - L152-4 (CNL1) Always 10 kΩ or higher

    5. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      w/o Intelligent Parking Assist System
      Tester Connection Condition Specified Condition
      L172-3 (CNH1) - Body ground Always Below 1 V
      L172-4 (CNL1) - Body ground Always Below 1 V
      w/ Intelligent Parking Assist System
      Tester Connection Condition Specified Condition
      L173-3 (CNH1) - Body ground Always Below 1 V
      L173-4 (CNL1) - Body ground Always Below 1 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. INSPECT COMBINATION METER SUB-ASSEMBLY


    1. Remove the combination meter sub-assembly Click here.

    2. A005DT6E08
      Text in Illustration
      *a

      Component without harness connected

      (Combination Meter Sub-assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      28 (MSCH) - 29 (MSCL) Always 108 to 132 Ω

    NG

    REPLACE COMBINATION METER SUB-ASSEMBLY Click here

    OK

  3. INSPECT NAVIGATION RECEIVER ASSEMBLY


    1. Remove the navigation receiver assembly Click here.

    2. A005DHYE02
      Text in Illustration
      *a

      Component without harness connected

      (Navigation Receiver Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 (CNH1) - 4 (CNL1) Always 108 to 132 Ω

    NG

    REPLACE NAVIGATION RECEIVER ASSEMBLY Click here

    OK

  4. REPLACE COMBINATION METER SUB-ASSEMBLY


    1. Replace the combination meter sub-assembly with a new or known good one Click here.

    2. Clear the DTCs Click here.

    3. Recheck for DTCs and check that no DTCs are output.

      OK
      No DTCs are output.

    NG

    REPLACE NAVIGATION RECEIVER ASSEMBLY Click here

    OK

  5. CHECK METER / GAUGE SYSTEM


    1. Turn the power switch on (IG) and wait 30 seconds.

    2. Operate the steering pad switch assembly and check that the audio tab is displayed on the multi-information display in the combination meter sub-assembly and the audio system can be operated normally.

      OK
      Audio system returns to normal.

    OK

    END

    NG

    REPLACE NAVIGATION RECEIVER ASSEMBLY Click here