8GR-FKS COOLANT REPLACEMENT

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

CAUTION:

Do not remove the radiator cap sub-assembly or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

B006B9K

PROCEDURE


  1. REMOVE V-BANK COVER SUB-ASSEMBLY

    Click here

  2. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

    Click here

  3. REMOVE TRANSMISSION UNDER COVER

    Click here

  4. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

    Click here

  5. REMOVE UPPER RADIATOR SUPPORT SEAL

    Click here

  6. REMOVE RADIATOR COVER PLATE

    Click here

  7. REMOVE LOWER RADIATOR AIR DEFLECTOR

    Click here

  8. DRAIN ENGINE COOLANT

    CAUTION:

    Do not remove the reserve tank cap, radiator cap sub-assembly or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


    1. B006DZ5C01
      *a Hose

      Connect a hose with an inside diameter of 9 mm (0.354 in.) to the radiator drain cock as shown in the illustration.

    2. B006DVYC01
      *a Hose

      Connect a hose with an inside diameter of 8 mm (0.315 in.) to the cylinder block water drain cock plug as shown in the illustration.

    3. Loosen the radiator drain cock plug.

      B006A6DC01
      *1 Radiator Drain Cock Plug *2 Radiator Cap Sub-assembly
      *3 Radiator Reserve Tank Assembly *4 Reserve Tank Cap
      *5 Cylinder Block Water Drain Cock Plug *6 No. 1 Radiator Hose
      *7 No. 3 Radiator Hose - -

    4. Remove the reserve tank cap. Then drain the engine coolant.

      Tech Tips

      Collect the engine coolant in a container and dispose of it according to the regulations in your area.

    5. Loosen the cylinder block drain cock plug.

    6. Tighten the cylinder block drain cock plug.

      Torque:
      12.7 N*m  { 130 kgf*cm, 9 ft.*lbf }

    7. Tighten the radiator drain cock plug by hand.

    8. Disconnect the hose from the cylinder block water drain cock plug.

    9. Disconnect the hose from the radiator drain cock.

  9. ADD ENGINE COOLANT

    CAUTION:

    Do not remove the reserve tank cap, radiator cap sub-assembly or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

    Note


    • Be sure to install the radiator cap sub-assembly and reserve tank cap in the correct positions since incorrect installation may cause a malfunction.

    • Do not substitute plain water for engine coolant.

    Tech Tips

    Before adding coolant, turn the A/C switch off.


    1. Remove the radiator cap sub-assembly and reserve tank cap.

    2. B006DDO

      Add engine coolant to the level shown in the illustration.

      Specified Capacity
      Item Specified Condition
      w/ In-tank Oil Cooler 10.9 liters (11.5 US qts, 9.6 Imp. qts)
      w/o In-tank Oil Cooler 11.0 liters (11.6 US qts, 9.7 Imp. qts)

      Note

      Do not substitute plain water for engine coolant.

      Tech Tips

      LEXUS vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damaging the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

    3. Squeeze the No. 1 radiator hose and No. 3 radiator hose several times by hand, and then check the level of the engine coolant.

      If the engine coolant level is low, add engine coolant.

    4. Install the reserve tank cap.

    5. Pour coolant of the specified concentration into the coolant filler hole on the engine side until the coolant level reaches the hole, and then install the radiator cap sub-assembly.

    6. Bleed air from the cooling system.

      Note


      • Before starting the engine, turn the A/C switch off.

      • Adjust the heater control to the maximum hot setting.

      • Adjust the blower speed to the low setting.


      1. Warm up the engine until the water inlet with thermostat sub-assembly opens. While the water inlet with thermostat sub-assembly is open, circulate the engine coolant for several minutes.

        Tech Tips

        The water inlet with thermostat sub-assembly open timing can be confirmed by squeezing the No. 3 radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the No. 3 radiator hose.

      2. Squeeze the No. 1 radiator hose and No. 3 radiator hose several times by hand to bleed air.

        CAUTION:


        • Because the engine, radiator assembly, No. 1 radiator hose and No. 3 radiator hose are extremely hot, do not perform these procedures without wearing protective gloves.

        • Performing these procedures without wearing protective gloves could result in burns.

        • When checking the thermostat open timing, do not touch rotating components such as the cooling fan.

        • Touching rotating components such as the cooling fan could result in your hand or clothing getting caught and pulled in.

        Note


        • Make sure that the radiator reserve tank assembly still has some engine coolant in it.

        • If the engine coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.

        • If there is not enough engine coolant, the engine may overheat or be seriously damaged.

        • If the radiator reserve tank assembly does not have enough engine coolant, perform the following: 1) stop the engine, 2) wait until the engine coolant cools down, and 3) add engine coolant until the radiator reserve tank assembly is filled to the full line.

    7. Stop the engine, and wait until the engine coolant cools down.

    8. Remove the reserve tank cap and check the engine coolant level.

      If the engine coolant level is low, add engine coolant.

    9. Add engine coolant to the F line on the radiator reserve tank assembly.

  10. INSPECT FOR COOLANT LEAK

    Click here

  11. INSTALL LOWER RADIATOR AIR DEFLECTOR

    Click here

  12. INSTALL UPPER RADIATOR SUPPORT SEAL

    Click here

  13. INSTALL RADIATOR COVER PLATE

    Click here

  14. INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

    Click here

  15. INSTALL TRANSMISSION UNDER COVER

    Click here

  16. INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

    Click here

  17. INSTALL V-BANK COVER SUB-ASSEMBLY

    Click here