SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P2009 and P2010

DTC Code DTC Name
P2009 Intake Manifold Runner Control Circuit Low (Bank 1)
P2010 Intake Manifold Runner Control Circuit High (Bank 1)

DESCRIPTION

The ECM activates the intake air control valve actuator (for tumble control valve), which opens and closes the Tumble Control Valve (TCV). The ECM activates the DC motor based on engine speed, coolant temperature, intake air temperature and other conditions.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

P2009

Intake Manifold Runner Control Circuit Low (Bank 1)

Both of the following conditions continue for 1 second (1 trip detection logic).

(a) The output duty of the intake air control valve actuator is 34% or higher.

(b) The current of the intake air control valve actuator is less than 0.35 A.

  • Open or short in intake air control valve actuator (for tumble control valve) circuit

  • Intake air control valve actuator (for tumble control valve)

  • Intake manifold

  • ECM

Comes on

DTC stored

P2010

Intake Manifold Runner Control Circuit High (Bank 1)

Either of the following conditions continues for 6 times or more (1 trip detection logic).

(a) The motor drive IC has overcurrent.

(b) The motor drive IC overheats.

  • Open or short in intake air control valve actuator (for tumble control valve) circuit

  • Intake air control valve actuator (for tumble control valve)

  • Intake manifold

  • ECM

Comes on

DTC stored

MONITOR DESCRIPTION

When the voltage of the intake air control valve actuator deviates from the standard range, the ECM determines that a malfunction has occurred and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components

Intake air control valve actuator (for tumble control valve)

Frequency of Operation

Continuous

COMPONENT OPERATING RANGE

Table 1. P2009

Intake air control valve actuator for tumble control valve current

Higher than 0.35 A
Table 2. P2010

Motor drive IC high current limiter monitor input

Pass

CONFIRMATION DRIVING PATTERN

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the engine switch off and wait for at least 30 seconds.

  6. Turn the engine switch on (IG) and turn the GTS on.

  7. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

  8. Check that the engine coolant temperature is 60°C (140°F) or higher.

  9. Wait approximately 10 seconds.

  10. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  11. Read the pending DTCs.

    Tip:

    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  12. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  13. Input the DTC: P2009 or P2010.

  14. Check the DTC judgment result.

    GTS Display

    Description

    NORMAL

    • DTC judgment completed

    • System normal

    ABNORMAL

    • DTC judgment completed

    • System abnormal

    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions

    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
    Tip:

    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

WIRING DIAGRAM

Refer to DTC P2004.

Click here

CAUTION / NOTICE / HINT

Tip:

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

  1. INSPECT INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)

    1. Inspect the intake air control valve actuator (for tumble control valve).

      Click here

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)

    Click here

    OK

  2. INSPECT INTAKE MANIFOLD (TUMBLE CONTROL VALVE OPERATION)

    1. Inspect the intake manifold for the tumble control valve operation.

      Click here

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE INTAKE MANIFOLD

    Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (INTAKE AIR CONTROL VALVE ACTUATOR - ECM)

    Click here

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK WHETHER DTC OUTPUT RECURS (DTC P2009 OR P2010)

    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.

      Click here

      Powertrain > Engine and ECT > Clear DTCs

    5. Turn the engine switch off and wait for at least 30 seconds.

    6. Turn the engine switch on (IG).

    7. Turn the GTS on.

    8. Wait approximately 10 seconds.

    9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    10. Read the DTCs.

      Powertrain > Engine and ECT > Trouble Codes

    Result

    Result

    Proceed to

    DTC P2009 or P2010 is output

    A

    DTC is not output

    B
    A

    REPLACE ECM

    Click here

    B

    CHECK FOR INTERMITTENT PROBLEMS

    Click here